► ICCONS® | Wire Brushes

Prepare Drilled Holes for Correct Anchor Installation A drilled hole can appear clear at the opening while fine drilling debris remains against the bore wall. ICCONS® | Wire Brushes are purpose-built hole-preparation accessories used before compatible anchor installations, helping crews clean drilled concrete holes according to the procedure required for...

Prepare Drilled Holes for Correct Anchor Installation

A drilled hole can appear clear at the opening while fine drilling debris remains against the bore wall. ICCONS® | Wire Brushes are purpose-built hole-preparation accessories used before compatible anchor installations, helping crews clean drilled concrete holes according to the procedure required for the fixing system.

For concreters, steel installers, builders & fixing contractors, brush selection starts with the specified hole diameter rather than the anchor's appearance or whichever accessory happens to be nearby. Prepare the drilling setup through  Concrete Cutting & Drilling Tools, match supporting equipment from  Drill Accessories or compare Anchor Bolts for adjoining anchoring requirements.

► Wire brushes for drilled-hole preparation
► Standard & performance brush options
► Multiple diameters for different drilled holes
► Extension accessories for increased reach
► SDS Plus adaptor options for powered preparation
► Accessories suited to ICCONS hole-cleaning procedures
► Useful across compatible chemical-anchor installations
► Options for varied hole diameters & embedment requirements

What Are ICCONS® Wire Brushes?

Unlike workshop wire brushes used across exposed metal, these ICCONS accessories work inside drilled anchor holes.

Their role is to disturb & remove drilling debris remaining against the bore wall as part of the applicable hole-cleaning procedure.

The ICCONS range includes related accessories such as:

► Wire Brushes
► Performance Wire Brushes
► Standard Brushes
► Wire Brush Extensions
► Performance Wire Brush Extensions
► SDS Plus adaptor options

Which combination belongs on the job depends on the anchor system, drill-hole diameter, depth & installation instructions.

The Bore Wall Matters as Much as the Hole Opening

Concrete drilling produces fine material throughout the hole, not only around the surface where the drill bit entered.

Residue can remain:

► Against the bore wall
► Near the bottom
► Inside irregularities in the concrete
► Along deeper portions of the embedment

Where an anchor system specifies hole cleaning, reaching the required depth with the drill bit is only one stage of preparation.

Brushing acts on material sitting against the bore wall while the associated debris-removal procedure clears loosened material from the hole.

For more context on the importance of treating the fixing as a complete system, read Why Good Fasteners Matter More Than the Tool You Drive Them With.

Choose the Brush From the Specified Drill Diameter

The drilled-hole dimension gives crews a practical starting point for identifying the appropriate brush.

Documented ICCONS standard wire-brush options cover numerous hole diameters:

Brush

Nominal Drill-Hole Diameter

CWB10

10 mm

CWB12

12 mm

CWB14

14 mm

CWB18

18 mm

CWB20

20 mm

CWB22

22 mm

CWB24

24 mm

CWB28

28 mm

CWB32

32 mm

CWB35

35 mm

CWB40

40 mm

CWB45

45 mm

CWB52

52 mm

CWB55

55 mm

Performance Wire Brushes provide further documented options across the ICCONS range.

Confirm the required accessory against the current installation information for the exact anchoring system before work begins.

Anchor Diameter & Drill-Hole Diameter Can Differ

Threaded rod size, reinforcing-bar diameter & the hole drilled into the base material should not be treated as interchangeable measurements.

Before selecting a brush, establish:

► Anchor element
► Specified drill diameter
► Required hole depth
► Selected adhesive or anchor system
► Required embedment
► Applicable preparation instructions

This distinction becomes particularly important in chemical anchoring, where the hole, adhesive, anchor element & installation method work together.

Choosing from the anchor diameter alone can result in the wrong cleaning accessory being sent to site.

Standard & Performance Brushes Belong to Defined Systems

Matching diameter is important but the brush family can matter as well.

ICCONS identifies standard wire brushes for applicable systems including BIS-P Gen2 & BIS-V.

Its Performance Wire Brush range supports other applicable anchoring systems, including:

► BIS-PE Gen3
► BIS-E
► BIS-HY Gen2
► VDP-Q Capsules

Check the documentation for the specific anchoring product rather than assuming a standard & performance brush of similar dimensions can always be substituted for one another.

Where the connection involves structural threaded hardware, browse  Structural Fasteners & Bolts for related fastening requirements.

Deep Holes Need Enough Working Reach

Correct brush diameter does little good when the accessory cannot reach the full depth that needs preparation.

ICCONS provides extensions for applicable wire-brush systems.

Before working on deeper embedments, check:

► Drilled depth
► Brush working length
► Extension requirement
► Connection compatibility
► Access around the hole
► Cleaning sequence

An extension allows the brush to reach further into deeper bores without changing the specified cleaning diameter.

Do not shorten the preparation depth simply because the basic brush arrangement cannot reach comfortably.

SDS Plus Adaptors Can Support Repetitive Preparation

A handful of accessible holes creates a different workload from preparing repeated anchor positions across a larger installation.

ICCONS provides SDS Plus adaptors for compatible threaded wire brushes.

Before assembling a powered setup, verify:

► Brush family
► Adaptor type
► Extension requirements
► Equipment compatibility
► Drill-hole diameter
► Required preparation method

For compatible drilling equipment around larger concrete-fixing work, browse  Hammer Drills.

Follow the applicable anchor instructions rather than assuming powered brushing changes the required cleaning sequence.

Brushing & Debris Removal Have Separate Roles

Disturbing material from the bore wall does not automatically remove that material from the hole.

ICCONS hole-preparation equipment includes wire brushes alongside an industrial hole-cleaning blow pump.

Depending on the anchoring system, the prescribed process can require repeated brushing & blowing stages.

Check:

► Drill-hole diameter
► Hole depth
► Brush specification
► Blow equipment
► Number of cleaning cycles
► Required sequence

Complete the process identified for the actual anchor product rather than using a habitual routine from another fixing system.

Chemical Anchoring Relies on More Than the Adhesive Cartridge

A suitable injection adhesive still needs the drilled hole to be prepared according to its installation requirements.

Chemical anchoring can bring together:

► Concrete or masonry substrate
► Drilled-hole diameter
► Embedment depth
► Anchor element
► Adhesive formulation
► Cleaning method
► Injection procedure
► Working time
► Cure time
► Installation temperature

Wire brushing occupies one defined stage within that larger installation.

For a broader explanation of common anchor & fixing families, the Fastener Guide Bolts Screws Anchors provides useful supporting information.

Post-Installed Rebar Can Demand Deeper Preparation

Reinforcing-bar installations can involve substantial embedment depths & preparation requirements that differ from smaller threaded anchors.

ICCONS documents brush options associated with reinforcing applications, including a 22 mm brush for applicable N20 rebar work.

Before preparing a rebar hole, confirm:

► Reinforcing-bar size
► Required drill diameter
► Embedment depth
► Adhesive system
► Brush family
► Extension requirements
► Cleaning procedure

Use the engineering requirements & current installation documentation governing the connection.

One documented rebar example should never be applied automatically to every post-installed reinforcing application.

A Clear Entrance Doesn't Confirm a Clean Bore

The first few centimetres of a drilled hole can look tidy while debris remains much deeper inside.

For deeper anchor positions, check that the preparation process addresses:

► Full specified depth
► Bore-wall contact
► Brush reach
► Loosened drilling material
► Debris remaining towards the bottom

Longer embedments make adequate reach particularly important.

Prepare the complete working depth rather than concentrating only on the visible entrance.

Inspect Brushes Before Repetitive Anchor Work

Bristle condition influences how effectively the accessory contacts the inside of the drilled hole.

Before a larger run of installations, inspect for:

► Worn bristles
► Distorted brush shape
► Loose components
► Damaged threads
► Contamination
► Poor connection to adaptors or extensions

Replace unsuitable accessories before beginning repetitive work.

Discovering a worn brush after numerous holes have already been processed can complicate an otherwise organised installation sequence.

For broader preparation ahead of busy site periods, Spring Jobsite Prep Getting Your Gear Ready covers practical tool & consumable readiness.

Make Brush Diameter Easy to Identify

Several hole-cleaning brushes stored together can become difficult to distinguish once packaging has been removed.

Organise the kit around:

► Brush diameter
► Standard or performance family
► Extension compatibility
► Adaptor type
► Intended anchor system

Clearly identified storage positions can help crews select the intended accessory during repeated drilling & anchoring work.

Where multiple chemical-anchor systems are used, keep the relevant preparation information accessible with the associated equipment.

Accurate Drilling Comes Before Cleaning

A wire brush cannot correct a hole that was drilled to an unsuitable diameter, depth or position.

Before preparation begins, verify:

► Set-out
► Drill-bit diameter
► Hole depth
► Base material
► Required spacing
► Edge conditions where applicable
► Anchor specification

Suitable  Measuring & Layout Tools can support accurate positioning before drilling starts.

If the drilled hole falls outside the specified requirements, determine the appropriate corrective action before proceeding with the anchor installation.

Repeated Anchor Holes Benefit From a Defined Work Sequence

Baseplates, brackets, rails & other multi-anchor installations can involve numerous holes moving through drilling, cleaning & fixing stages.

Keep the required equipment organised around that sequence:

► Drill bits
► Hole-cleaning brushes
► Blow equipment
► Extensions
► Adaptors
► Adhesive equipment
► Anchor elements

Where practical, distinguish holes that have completed the specified preparation from those still awaiting cleaning.

A controlled sequence becomes increasingly valuable as the number of anchor positions grows.

Keep Prepared Holes From Being Contaminated Again

Cleaning a bore does not prevent new dust, debris or moisture entering while surrounding work continues.

If installation does not immediately follow preparation, consider:

► Nearby drilling activity
► Concrete dust
► Water exposure
► Other construction debris
► Time between cleaning & installation

Reassess the hole before installing the anchor.

Where the applicable procedure requires preparation to be repeated after contamination or delay, complete that work before progressing.

Check the Complete Accessory Combination Before Mobilising

A brush, extension & adaptor only form a useful setup when their connections & working dimensions suit the planned installation.

Before sending the equipment to site, confirm:

► Required brush
► Correct diameter
► Standard or performance family
► Extension compatibility
► SDS Plus adaptor where applicable
► Drilling equipment
► Blow equipment
► Anchor system

For additional equipment used around drilling & installation work, Power Tool Accessories provides a supporting range for compatible site setups.

Checking the combination beforehand can prevent a small missing accessory from interrupting an otherwise prepared anchoring job.

Why Source ICCONS® Wire Brushes Through Industrial Shed?

Hole-preparation equipment is easier to organise when brush diameter, drilling accessories & the intended anchor system are considered together.

Industrial Shed supplies drilling accessories, fixing equipment & construction hardware for concreters, builders, steel installers & contractors working across concrete anchoring, structural installation & general construction.

For crews managing recurring equipment & consumable requirements, Warranty & parts Support provides assistance around supported equipment purchased through Industrial Shed.

Need to confirm a brush, adaptor or extension combination? Contact Us with the ICCONS anchor system, specified hole diameter & required depth.

Give the Full Embedment the Preparation It Requires

The anchor eventually disappears into the concrete but the condition of that drilled hole remains part of the connection.

Select the ICCONS Wire Brush that corresponds with the specified hole diameter & anchoring system, check that the setup reaches the required depth then complete every brushing & debris-removal stage called for by the installation procedure.

Deeper embedments, chemical anchors & post-installed reinforcing work deserve particular attention because correct accessory selection must continue through the full working depth.

Choose ICCONS Wire Brushes for purpose-matched drilled-hole preparation across compatible concrete anchoring & post-installed fixing applications.

Frequently Asked Questions

What are ICCONS Wire Brushes used for?

ICCONS Wire Brushes are used as part of drilled-hole preparation for compatible anchor installations, helping remove drilling debris from the bore.

Are ICCONS Wire Brushes general-purpose rust-removal brushes?

This range is intended for drilled anchor-hole preparation rather than general surface rust removal, weld cleaning or metal finishing.

How do I determine the correct brush diameter?

Use the drill-hole diameter specified for the exact anchor system then confirm the corresponding brush in the applicable installation information.

Can ICCONS Wire Brushes connect to SDS Plus equipment?

Applicable threaded wire brushes can be used with the corresponding ICCONS SDS Plus adaptor. Confirm the brush, adaptor, extension & equipment combination before use.

When should a wire-brush extension be used?

An extension provides additional reach where the required preparation depth exceeds the practical working length of the standard brush arrangement.

Does brushing replace blowing the anchor hole?

Not where the anchor system specifies both processes. Brushing acts on material at the bore wall while the prescribed debris-removal procedure clears loosened material from the hole.

Brands

► ICCONS® | Wire Brushes

Prepare Drilled Holes for Correct Anchor Installation

A drilled hole can appear clear at the opening while fine drilling debris remains against the bore wall. ICCONS® | Wire Brushes are purpose-built hole-preparation accessories used before compatible anchor installations, helping crews clean drilled concrete holes according to the procedure required for the fixing system.

For concreters, steel installers, builders & fixing contractors, brush selection starts with the specified hole diameter rather than the anchor's appearance or whichever accessory happens to be nearby. Prepare the drilling setup through  Concrete Cutting & Drilling Tools, match supporting equipment from  Drill Accessories or compare Anchor Bolts for adjoining anchoring requirements.

► Wire brushes for drilled-hole preparation
► Standard & performance brush options
► Multiple diameters for different drilled holes
► Extension accessories for increased reach
► SDS Plus adaptor options for powered preparation
► Accessories suited to ICCONS hole-cleaning procedures
► Useful across compatible chemical-anchor installations
► Options for varied hole diameters & embedment requirements

What Are ICCONS® Wire Brushes?

Unlike workshop wire brushes used across exposed metal, these ICCONS accessories work inside drilled anchor holes.

Their role is to disturb & remove drilling debris remaining against the bore wall as part of the applicable hole-cleaning procedure.

The ICCONS range includes related accessories such as:

► Wire Brushes
► Performance Wire Brushes
► Standard Brushes
► Wire Brush Extensions
► Performance Wire Brush Extensions
► SDS Plus adaptor options

Which combination belongs on the job depends on the anchor system, drill-hole diameter, depth & installation instructions.

The Bore Wall Matters as Much as the Hole Opening

Concrete drilling produces fine material throughout the hole, not only around the surface where the drill bit entered.

Residue can remain:

► Against the bore wall
► Near the bottom
► Inside irregularities in the concrete
► Along deeper portions of the embedment

Where an anchor system specifies hole cleaning, reaching the required depth with the drill bit is only one stage of preparation.

Brushing acts on material sitting against the bore wall while the associated debris-removal procedure clears loosened material from the hole.

For more context on the importance of treating the fixing as a complete system, read Why Good Fasteners Matter More Than the Tool You Drive Them With.

Choose the Brush From the Specified Drill Diameter

The drilled-hole dimension gives crews a practical starting point for identifying the appropriate brush.

Documented ICCONS standard wire-brush options cover numerous hole diameters:

Brush

Nominal Drill-Hole Diameter

CWB10

10 mm

CWB12

12 mm

CWB14

14 mm

CWB18

18 mm

CWB20

20 mm

CWB22

22 mm

CWB24

24 mm

CWB28

28 mm

CWB32

32 mm

CWB35

35 mm

CWB40

40 mm

CWB45

45 mm

CWB52

52 mm

CWB55

55 mm

Performance Wire Brushes provide further documented options across the ICCONS range.

Confirm the required accessory against the current installation information for the exact anchoring system before work begins.

Anchor Diameter & Drill-Hole Diameter Can Differ

Threaded rod size, reinforcing-bar diameter & the hole drilled into the base material should not be treated as interchangeable measurements.

Before selecting a brush, establish:

► Anchor element
► Specified drill diameter
► Required hole depth
► Selected adhesive or anchor system
► Required embedment
► Applicable preparation instructions

This distinction becomes particularly important in chemical anchoring, where the hole, adhesive, anchor element & installation method work together.

Choosing from the anchor diameter alone can result in the wrong cleaning accessory being sent to site.

Standard & Performance Brushes Belong to Defined Systems

Matching diameter is important but the brush family can matter as well.

ICCONS identifies standard wire brushes for applicable systems including BIS-P Gen2 & BIS-V.

Its Performance Wire Brush range supports other applicable anchoring systems, including:

► BIS-PE Gen3
► BIS-E
► BIS-HY Gen2
► VDP-Q Capsules

Check the documentation for the specific anchoring product rather than assuming a standard & performance brush of similar dimensions can always be substituted for one another.

Where the connection involves structural threaded hardware, browse  Structural Fasteners & Bolts for related fastening requirements.

Deep Holes Need Enough Working Reach

Correct brush diameter does little good when the accessory cannot reach the full depth that needs preparation.

ICCONS provides extensions for applicable wire-brush systems.

Before working on deeper embedments, check:

► Drilled depth
► Brush working length
► Extension requirement
► Connection compatibility
► Access around the hole
► Cleaning sequence

An extension allows the brush to reach further into deeper bores without changing the specified cleaning diameter.

Do not shorten the preparation depth simply because the basic brush arrangement cannot reach comfortably.

SDS Plus Adaptors Can Support Repetitive Preparation

A handful of accessible holes creates a different workload from preparing repeated anchor positions across a larger installation.

ICCONS provides SDS Plus adaptors for compatible threaded wire brushes.

Before assembling a powered setup, verify:

► Brush family
► Adaptor type
► Extension requirements
► Equipment compatibility
► Drill-hole diameter
► Required preparation method

For compatible drilling equipment around larger concrete-fixing work, browse  Hammer Drills.

Follow the applicable anchor instructions rather than assuming powered brushing changes the required cleaning sequence.

Brushing & Debris Removal Have Separate Roles

Disturbing material from the bore wall does not automatically remove that material from the hole.

ICCONS hole-preparation equipment includes wire brushes alongside an industrial hole-cleaning blow pump.

Depending on the anchoring system, the prescribed process can require repeated brushing & blowing stages.

Check:

► Drill-hole diameter
► Hole depth
► Brush specification
► Blow equipment
► Number of cleaning cycles
► Required sequence

Complete the process identified for the actual anchor product rather than using a habitual routine from another fixing system.

Chemical Anchoring Relies on More Than the Adhesive Cartridge

A suitable injection adhesive still needs the drilled hole to be prepared according to its installation requirements.

Chemical anchoring can bring together:

► Concrete or masonry substrate
► Drilled-hole diameter
► Embedment depth
► Anchor element
► Adhesive formulation
► Cleaning method
► Injection procedure
► Working time
► Cure time
► Installation temperature

Wire brushing occupies one defined stage within that larger installation.

For a broader explanation of common anchor & fixing families, the Fastener Guide Bolts Screws Anchors provides useful supporting information.

Post-Installed Rebar Can Demand Deeper Preparation

Reinforcing-bar installations can involve substantial embedment depths & preparation requirements that differ from smaller threaded anchors.

ICCONS documents brush options associated with reinforcing applications, including a 22 mm brush for applicable N20 rebar work.

Before preparing a rebar hole, confirm:

► Reinforcing-bar size
► Required drill diameter
► Embedment depth
► Adhesive system
► Brush family
► Extension requirements
► Cleaning procedure

Use the engineering requirements & current installation documentation governing the connection.

One documented rebar example should never be applied automatically to every post-installed reinforcing application.

A Clear Entrance Doesn't Confirm a Clean Bore

The first few centimetres of a drilled hole can look tidy while debris remains much deeper inside.

For deeper anchor positions, check that the preparation process addresses:

► Full specified depth
► Bore-wall contact
► Brush reach
► Loosened drilling material
► Debris remaining towards the bottom

Longer embedments make adequate reach particularly important.

Prepare the complete working depth rather than concentrating only on the visible entrance.

Inspect Brushes Before Repetitive Anchor Work

Bristle condition influences how effectively the accessory contacts the inside of the drilled hole.

Before a larger run of installations, inspect for:

► Worn bristles
► Distorted brush shape
► Loose components
► Damaged threads
► Contamination
► Poor connection to adaptors or extensions

Replace unsuitable accessories before beginning repetitive work.

Discovering a worn brush after numerous holes have already been processed can complicate an otherwise organised installation sequence.

For broader preparation ahead of busy site periods, Spring Jobsite Prep Getting Your Gear Ready covers practical tool & consumable readiness.

Make Brush Diameter Easy to Identify

Several hole-cleaning brushes stored together can become difficult to distinguish once packaging has been removed.

Organise the kit around:

► Brush diameter
► Standard or performance family
► Extension compatibility
► Adaptor type
► Intended anchor system

Clearly identified storage positions can help crews select the intended accessory during repeated drilling & anchoring work.

Where multiple chemical-anchor systems are used, keep the relevant preparation information accessible with the associated equipment.

Accurate Drilling Comes Before Cleaning

A wire brush cannot correct a hole that was drilled to an unsuitable diameter, depth or position.

Before preparation begins, verify:

► Set-out
► Drill-bit diameter
► Hole depth
► Base material
► Required spacing
► Edge conditions where applicable
► Anchor specification

Suitable  Measuring & Layout Tools can support accurate positioning before drilling starts.

If the drilled hole falls outside the specified requirements, determine the appropriate corrective action before proceeding with the anchor installation.

Repeated Anchor Holes Benefit From a Defined Work Sequence

Baseplates, brackets, rails & other multi-anchor installations can involve numerous holes moving through drilling, cleaning & fixing stages.

Keep the required equipment organised around that sequence:

► Drill bits
► Hole-cleaning brushes
► Blow equipment
► Extensions
► Adaptors
► Adhesive equipment
► Anchor elements

Where practical, distinguish holes that have completed the specified preparation from those still awaiting cleaning.

A controlled sequence becomes increasingly valuable as the number of anchor positions grows.

Keep Prepared Holes From Being Contaminated Again

Cleaning a bore does not prevent new dust, debris or moisture entering while surrounding work continues.

If installation does not immediately follow preparation, consider:

► Nearby drilling activity
► Concrete dust
► Water exposure
► Other construction debris
► Time between cleaning & installation

Reassess the hole before installing the anchor.

Where the applicable procedure requires preparation to be repeated after contamination or delay, complete that work before progressing.

Check the Complete Accessory Combination Before Mobilising

A brush, extension & adaptor only form a useful setup when their connections & working dimensions suit the planned installation.

Before sending the equipment to site, confirm:

► Required brush
► Correct diameter
► Standard or performance family
► Extension compatibility
► SDS Plus adaptor where applicable
► Drilling equipment
► Blow equipment
► Anchor system

For additional equipment used around drilling & installation work, Power Tool Accessories provides a supporting range for compatible site setups.

Checking the combination beforehand can prevent a small missing accessory from interrupting an otherwise prepared anchoring job.