Prepare Drilled Holes for Correct Anchor Installation
A drilled hole can appear clear at the opening while fine drilling debris remains against the bore wall. ICCONS® | Wire Brushes are purpose-built hole-preparation accessories used before compatible anchor installations, helping crews clean drilled concrete holes according to the procedure required for the fixing system.
For concreters, steel installers, builders & fixing contractors, brush selection starts with the specified hole diameter rather than the anchor's appearance or whichever accessory happens to be nearby. Prepare the drilling setup through Concrete Cutting & Drilling Tools, match supporting equipment from Drill Accessories or compare Anchor Bolts for adjoining anchoring requirements.
► Wire brushes for drilled-hole preparation
► Standard & performance brush options
► Multiple diameters for different drilled holes
► Extension accessories for increased reach
► SDS Plus adaptor options for powered preparation
► Accessories suited to ICCONS hole-cleaning procedures
► Useful across compatible chemical-anchor installations
► Options for varied hole diameters & embedment requirements
What Are ICCONS® Wire Brushes?
Unlike workshop wire brushes used across exposed metal, these ICCONS accessories work inside drilled anchor holes.
Their role is to disturb & remove drilling debris remaining against the bore wall as part of the applicable hole-cleaning procedure.
The ICCONS range includes related accessories such as:
► Wire Brushes
► Performance Wire Brushes
► Standard Brushes
► Wire Brush Extensions
► Performance Wire Brush Extensions
► SDS Plus adaptor options
Which combination belongs on the job depends on the anchor system, drill-hole diameter, depth & installation instructions.
The Bore Wall Matters as Much as the Hole Opening
Concrete drilling produces fine material throughout the hole, not only around the surface where the drill bit entered.
Residue can remain:
► Against the bore wall
► Near the bottom
► Inside irregularities in the concrete
► Along deeper portions of the embedment
Where an anchor system specifies hole cleaning, reaching the required depth with the drill bit is only one stage of preparation.
Brushing acts on material sitting against the bore wall while the associated debris-removal procedure clears loosened material from the hole.
For more context on the importance of treating the fixing as a complete system, read Why Good Fasteners Matter More Than the Tool You Drive Them With.
Choose the Brush From the Specified Drill Diameter
The drilled-hole dimension gives crews a practical starting point for identifying the appropriate brush.
Documented ICCONS standard wire-brush options cover numerous hole diameters:
|
Brush
|
Nominal Drill-Hole Diameter
|
|
CWB10
|
10 mm
|
|
CWB12
|
12 mm
|
|
CWB14
|
14 mm
|
|
CWB18
|
18 mm
|
|
CWB20
|
20 mm
|
|
CWB22
|
22 mm
|
|
CWB24
|
24 mm
|
|
CWB28
|
28 mm
|
|
CWB32
|
32 mm
|
|
CWB35
|
35 mm
|
|
CWB40
|
40 mm
|
|
CWB45
|
45 mm
|
|
CWB52
|
52 mm
|
|
CWB55
|
55 mm
|
Performance Wire Brushes provide further documented options across the ICCONS range.
Confirm the required accessory against the current installation information for the exact anchoring system before work begins.
Anchor Diameter & Drill-Hole Diameter Can Differ
Threaded rod size, reinforcing-bar diameter & the hole drilled into the base material should not be treated as interchangeable measurements.
Before selecting a brush, establish:
► Anchor element
► Specified drill diameter
► Required hole depth
► Selected adhesive or anchor system
► Required embedment
► Applicable preparation instructions
This distinction becomes particularly important in chemical anchoring, where the hole, adhesive, anchor element & installation method work together.
Choosing from the anchor diameter alone can result in the wrong cleaning accessory being sent to site.
Standard & Performance Brushes Belong to Defined Systems
Matching diameter is important but the brush family can matter as well.
ICCONS identifies standard wire brushes for applicable systems including BIS-P Gen2 & BIS-V.
Its Performance Wire Brush range supports other applicable anchoring systems, including:
► BIS-PE Gen3
► BIS-E
► BIS-HY Gen2
► VDP-Q Capsules
Check the documentation for the specific anchoring product rather than assuming a standard & performance brush of similar dimensions can always be substituted for one another.
Where the connection involves structural threaded hardware, browse Structural Fasteners & Bolts for related fastening requirements.
Deep Holes Need Enough Working Reach
Correct brush diameter does little good when the accessory cannot reach the full depth that needs preparation.
ICCONS provides extensions for applicable wire-brush systems.
Before working on deeper embedments, check:
► Drilled depth
► Brush working length
► Extension requirement
► Connection compatibility
► Access around the hole
► Cleaning sequence
An extension allows the brush to reach further into deeper bores without changing the specified cleaning diameter.
Do not shorten the preparation depth simply because the basic brush arrangement cannot reach comfortably.
SDS Plus Adaptors Can Support Repetitive Preparation
A handful of accessible holes creates a different workload from preparing repeated anchor positions across a larger installation.
ICCONS provides SDS Plus adaptors for compatible threaded wire brushes.
Before assembling a powered setup, verify:
► Brush family
► Adaptor type
► Extension requirements
► Equipment compatibility
► Drill-hole diameter
► Required preparation method
For compatible drilling equipment around larger concrete-fixing work, browse Hammer Drills.
Follow the applicable anchor instructions rather than assuming powered brushing changes the required cleaning sequence.
Brushing & Debris Removal Have Separate Roles
Disturbing material from the bore wall does not automatically remove that material from the hole.
ICCONS hole-preparation equipment includes wire brushes alongside an industrial hole-cleaning blow pump.
Depending on the anchoring system, the prescribed process can require repeated brushing & blowing stages.
Check:
► Drill-hole diameter
► Hole depth
► Brush specification
► Blow equipment
► Number of cleaning cycles
► Required sequence
Complete the process identified for the actual anchor product rather than using a habitual routine from another fixing system.
Chemical Anchoring Relies on More Than the Adhesive Cartridge
A suitable injection adhesive still needs the drilled hole to be prepared according to its installation requirements.
Chemical anchoring can bring together:
► Concrete or masonry substrate
► Drilled-hole diameter
► Embedment depth
► Anchor element
► Adhesive formulation
► Cleaning method
► Injection procedure
► Working time
► Cure time
► Installation temperature
Wire brushing occupies one defined stage within that larger installation.
For a broader explanation of common anchor & fixing families, the Fastener Guide Bolts Screws Anchors provides useful supporting information.
Post-Installed Rebar Can Demand Deeper Preparation
Reinforcing-bar installations can involve substantial embedment depths & preparation requirements that differ from smaller threaded anchors.
ICCONS documents brush options associated with reinforcing applications, including a 22 mm brush for applicable N20 rebar work.
Before preparing a rebar hole, confirm:
► Reinforcing-bar size
► Required drill diameter
► Embedment depth
► Adhesive system
► Brush family
► Extension requirements
► Cleaning procedure
Use the engineering requirements & current installation documentation governing the connection.
One documented rebar example should never be applied automatically to every post-installed reinforcing application.
A Clear Entrance Doesn't Confirm a Clean Bore
The first few centimetres of a drilled hole can look tidy while debris remains much deeper inside.
For deeper anchor positions, check that the preparation process addresses:
► Full specified depth
► Bore-wall contact
► Brush reach
► Loosened drilling material
► Debris remaining towards the bottom
Longer embedments make adequate reach particularly important.
Prepare the complete working depth rather than concentrating only on the visible entrance.
Inspect Brushes Before Repetitive Anchor Work
Bristle condition influences how effectively the accessory contacts the inside of the drilled hole.
Before a larger run of installations, inspect for:
► Worn bristles
► Distorted brush shape
► Loose components
► Damaged threads
► Contamination
► Poor connection to adaptors or extensions
Replace unsuitable accessories before beginning repetitive work.
Discovering a worn brush after numerous holes have already been processed can complicate an otherwise organised installation sequence.
For broader preparation ahead of busy site periods, Spring Jobsite Prep Getting Your Gear Ready covers practical tool & consumable readiness.
Make Brush Diameter Easy to Identify
Several hole-cleaning brushes stored together can become difficult to distinguish once packaging has been removed.
Organise the kit around:
► Brush diameter
► Standard or performance family
► Extension compatibility
► Adaptor type
► Intended anchor system
Clearly identified storage positions can help crews select the intended accessory during repeated drilling & anchoring work.
Where multiple chemical-anchor systems are used, keep the relevant preparation information accessible with the associated equipment.
Accurate Drilling Comes Before Cleaning
A wire brush cannot correct a hole that was drilled to an unsuitable diameter, depth or position.
Before preparation begins, verify:
► Set-out
► Drill-bit diameter
► Hole depth
► Base material
► Required spacing
► Edge conditions where applicable
► Anchor specification
Suitable Measuring & Layout Tools can support accurate positioning before drilling starts.
If the drilled hole falls outside the specified requirements, determine the appropriate corrective action before proceeding with the anchor installation.
Repeated Anchor Holes Benefit From a Defined Work Sequence
Baseplates, brackets, rails & other multi-anchor installations can involve numerous holes moving through drilling, cleaning & fixing stages.
Keep the required equipment organised around that sequence:
► Drill bits
► Hole-cleaning brushes
► Blow equipment
► Extensions
► Adaptors
► Adhesive equipment
► Anchor elements
Where practical, distinguish holes that have completed the specified preparation from those still awaiting cleaning.
A controlled sequence becomes increasingly valuable as the number of anchor positions grows.
Keep Prepared Holes From Being Contaminated Again
Cleaning a bore does not prevent new dust, debris or moisture entering while surrounding work continues.
If installation does not immediately follow preparation, consider:
► Nearby drilling activity
► Concrete dust
► Water exposure
► Other construction debris
► Time between cleaning & installation
Reassess the hole before installing the anchor.
Where the applicable procedure requires preparation to be repeated after contamination or delay, complete that work before progressing.
Check the Complete Accessory Combination Before Mobilising
A brush, extension & adaptor only form a useful setup when their connections & working dimensions suit the planned installation.
Before sending the equipment to site, confirm:
► Required brush
► Correct diameter
► Standard or performance family
► Extension compatibility
► SDS Plus adaptor where applicable
► Drilling equipment
► Blow equipment
► Anchor system
For additional equipment used around drilling & installation work, Power Tool Accessories provides a supporting range for compatible site setups.
Checking the combination beforehand can prevent a small missing accessory from interrupting an otherwise prepared anchoring job.