Cut-to-Length Stainless Banding for Custom Clamping Jobs
When a standard clamp won't match the diameter in front of you, continuous banding gives you room to work with the actual connection. Hardie Hose Bands provide cut-to-length stainless steel banding for suitable hose, ducting, pipework & industrial clamping jobs, allowing workshops & field crews to prepare clamps for the required circumference.
Choose from Bandimex 304 stainless steel band in five widths from 6.4mm to 19.1mm, or 12mm stainless steel Wormdrive Continuous Band. Each option is supplied in a 30m roll, making it practical for repeat maintenance, varied diameters & custom clamping work.
► Bandimex 304 stainless steel band
► 6.4mm, 9.5mm, 12.7mm, 15.8mm & 19.1mm widths
► 30m Bandimex rolls
► 12mm x 30m Wormdrive Continuous Band
► Cut material to suit the required clamp circumference
► Pair with the corresponding buckle or fastening system
► Practical stock for workshops, field service & maintenance crews
What Are Hardie Hose Bands?
Instead of starting with a finished clamp of predetermined diameter, continuous banding starts with a roll. Material is measured, cut to the required length & secured with the corresponding fastening component to create a clamp for a suitable installation.
That flexibility can be useful when:
► Connection diameters vary from job to job
► Large or uncommon clamp sizes are required
► Maintenance vehicles need adaptable repair stock
► Workshops regularly work across different hose or duct sizes
► Multiple clamps can be produced from one roll
The collection contains two separate systems:
|
Band System
|
Available Format
|
|
Bandimex 304
|
6.4–19.1mm widths x 30m
|
|
Wormdrive Continuous Band
|
12mm x 30m
|
Although both are continuous stainless banding, keep each system with its corresponding fastening components.
Why Choose Hardie Hose Bands?
Keeping continuous banding on the shelf can solve a problem that a drawer full of fixed-size clamps can't: an installation diameter you didn't know you'd need.
Five Bandimex Widths
Bandimex 304 band is available in 6.4mm, 9.5mm, 12.7mm, 15.8mm & 19.1mm widths, allowing the strip width to be selected for the corresponding clamping requirement.
304 Stainless Steel Construction
Clamping hardware often works where moisture, dirt & weather are part of the environment. The Bandimex products in this range are listed in 304 stainless steel.
30m Roll Format
A continuous 30m roll provides material for multiple clamps where the same band specification is suitable.
Wormdrive Alternative
For jobs using the corresponding wormdrive system, HC-WDCB provides 12mm-wide stainless steel continuous band in a 30m roll.
Less Dependence on Predetermined Diameters
The useful dimension isn't printed on a finished clamp – it's measured at the job. Continuous banding allows the installer to prepare an appropriate length rather than searching only among fixed circumferences.
Common Applications
Large-Diameter Hose Connections
Oversized hose connections can quickly expose gaps in a fixed-clamp inventory. Where continuous banding is suitable, material can be prepared for the circumference actually required.
Flexible Ducting
Different duct diameters, adaptors & joins can require clamps outside the sizes routinely kept in a workshop.
Pump & Transfer-Hose Installations
Pumps & transfer systems often combine hose, fittings & connections of different diameters. Suitable stainless banding provides an adaptable clamping option for maintenance & installation work.
Browse Irrigation Systems & Pumps for related pump & transfer equipment.
Agricultural Maintenance
Farm workshops & service vehicles can use continuous banding for compatible repairs where machinery or transfer equipment presents an uncommon clamp circumference.
Ducting & Ventilation Work
A long duct run can involve several connection sizes before the installation is finished. Continuous band allows suitable clamps to be prepared individually rather than relying exclusively on pre-sized hardware.
Field-Service Vehicles
Carrying selected rolls & their corresponding fasteners can cover multiple suitable diameters without filling storage compartments with dozens of finished clamp sizes.
Product Selection Guide
Don't choose the roll from diameter alone. First establish the banding system, then width, material requirements & the amount needed around the connection.
Hardie Hose Band Range
|
Product
|
Width
|
Material
|
Roll
|
Code
|
|
Bandimex Band 304
|
6.4mm
|
304 Stainless Steel
|
30m
|
HC-B202
|
|
Bandimex Band 304
|
9.5mm
|
304 Stainless Steel
|
30m
|
HC-B203
|
|
Bandimex Band 304
|
12.7mm
|
304 Stainless Steel
|
30m
|
HC-B204
|
|
Bandimex Band 304
|
15.8mm
|
304 Stainless Steel
|
30m
|
HC-B205
|
|
Bandimex Band 304
|
19.1mm
|
304 Stainless Steel
|
30m
|
HC-B206
|
|
Wormdrive Continuous Band
|
12mm
|
Stainless Steel
|
30m
|
HC-WDCB
|
Step 1 – Identify the Banding System
Determine whether the job calls for the Bandimex or corresponding wormdrive system.
Step 2 – Select the Required Width
For Bandimex, available widths are:
6.4mm → 9.5mm → 12.7mm → 15.8mm → 19.1mm
Wormdrive Continuous Band is listed at 12mm wide.
Step 3 – Measure the Connection
Measure the circumference where the clamp will sit rather than estimating from a nearby component.
Step 4 – Allow for the Fastening Method
Don't cut at the bare circumference measurement. Allow the additional material required by the corresponding buckle or fastening procedure.
Step 5 – Confirm Material Suitability
Consider the operating environment, including moisture, temperature & chemical exposure where relevant.
Step 6 – Prepare the Correct Tools
Use suitable equipment for cutting, tensioning & securing the selected banding system.
Bandimex or Wormdrive – Which System Fits the Job?
The two options provide continuous banding in different formats, so the fastening method is a useful place to start the decision.
|
Feature
|
Bandimex 304
|
Wormdrive Continuous Band
|
|
Widths
|
6.4–19.1mm
|
12mm
|
|
Roll length
|
30m
|
30m
|
|
Listed material
|
304 stainless steel
|
Stainless steel
|
|
Fastener
|
Corresponding Bandimex buckle
|
Corresponding W2 wormdrive buckle
|
|
Custom cut length
|
Yes
|
Yes
|
|
Mix components between systems?
|
No
|
No
|
Use each band with the fastening components intended for that system rather than selecting parts simply because their dimensions appear similar.
Match Bandimex Band with the Corresponding Buckle
Band & buckle should be checked as a pair before the cutter comes out.
|
Band Width
|
Band Code
|
Corresponding Buckle
|
|
6.4mm
|
HC-B202
|
6.4mm
|
|
9.5mm
|
HC-B203
|
9.5mm
|
|
12.7mm
|
HC-B204
|
12.7mm
|
|
15.8mm
|
HC-B205
|
15.8mm
|
|
19.1mm
|
HC-B206
|
19.1mm
|
Find the matching locking components in Hardie Hose | Buckles.
Ordering the corresponding buckle width with the band helps keep the complete clamping system ready for use.
Band Width Isn't Clamp Diameter
A 12.7mm band doesn't make a 12.7mm-diameter clamp. These measurements describe completely different parts of the installation.
|
Measurement
|
What It Means
|
|
Band width
|
Width of the stainless strip
|
|
Connection diameter
|
Diameter of the object being clamped
|
|
Circumference
|
Distance around the connection
|
|
Cut length
|
Band required to complete the clamp
|
For example, HC-B204 is 12.7mm-wide Bandimex band supplied on a 30m roll. The installer cuts the required length according to the connection circumference & applicable fastening method.
How Much Band Will a 30m Roll Make?
The answer depends on the circumference of each installation rather than band width alone.
A practical planning calculation is:
Material per clamp = connection circumference + fastening allowance
Then:
Approximate clamps per roll = usable roll length ÷ material required per clamp
Suppose a workshop is preparing several identical duct clamps. Instead of estimating every piece, complete the first clamp, confirm the cut length & use that verified measurement for the remaining identical connections.
That first completed clamp can prevent the same measuring error being repeated across an entire batch.
A Field-Service Example
A service vehicle reaches a pump installation where a large transfer-hose connection needs a replacement clamp, but none of the pre-sized clamps on board matches the circumference.
Where the appropriate continuous-band system is suitable, the technician can:
Identify the required system
Select the correct band width
Measure the connection
Allow for the fastening method
Cut the required length
Install the corresponding buckle
Tension & finish the clamp correctly
Inspect the completed connection
The remaining roll stays available for other compatible jobs, even when their circumferences differ.
Expert Tips
Keep Band & Buckles Together
A perfectly stocked band rack won't finish the job if the corresponding buckles have run out. Treat compatible banding & fastening components as one stock requirement.
Confirm One Clamp Before Batch Cutting
When preparing multiple identical clamps, install & inspect the first one before cutting every remaining piece.
Write Width & Code on the Roll Location
“Stainless band” is too vague once several widths are on the shelf. Labels such as “15.8mm Bandimex – HC-B205” make identification faster.
Keep Wormdrive Components Separate
Store wormdrive band & buckles apart from Bandimex components so similar-looking parts don't become mixed.
Protect Hands Around Cut Strip
Stainless banding can leave sharp cut edges. Use suitable cutting equipment & appropriate PPE during preparation & installation.
Fix Position Before Applying Final Tension
A poorly positioned clamp shouldn't be corrected by simply pulling it tighter. Reposition the band first.
Check the Connection Beneath the Clamp
New stainless banding won't repair a damaged hose or fitting underneath it. Inspect the accessible connection before installing the replacement clamp.
When Existing Banding Needs Attention?
A loose clamp is a symptom worth investigating, not an automatic instruction to tighten harder.
Check for:
► Loose or displaced banding
► Bent or damaged fastening components
► Cuts, distortion or deterioration in the band
► Leakage around the connection
► Movement beneath the clamp
► Hose or duct damage
► Evidence of excessive tightening
► Corrosion or environmental deterioration
Where a connection repeatedly loosens, inspect the complete arrangement to determine why movement is occurring before replacing the band.
Before the Cutter Touches the Roll
Stainless band is easier to shorten than it is to put back together, so confirm the setup first.
Check:
► Banding system
► Band width
► Corresponding buckle or fastener
► Connection circumference
► Required fastening allowance
► Material suitability
► Cutting & tensioning equipment
► Clamp position
Cut stainless strip can have sharp edges & tensioned banding can release energy if handled incorrectly. Use suitable PPE & follow the applicable installation instructions.