Galvanised Mesh Gates From 2400mm To 4200mm
Wide rural openings need a gate selected around more than the distance between two posts. Rally N Brace farm gates combine a 25NB tubular frame with graduated galvanised mesh for internal fence & boundary-fence applications, with actual lengths of 2400mm, 3000mm, 3600mm & 4200mm. Complete the wider fence line with Rally Fencing Supplies while Measuring & Layout Tools help establish openings, post positions & clearances before installation.
Graduated mesh is a defining feature of this Rally gate family. Smaller openings are positioned towards the bottom before increasing through the middle & upper sections, with 5mm wire used throughout the mesh infill.
All four sizes share a 1170mm actual height & 2mm tube wall thickness. Choose the gate around the measured opening, intended hardware arrangement, surrounding fence & access requirements rather than treating its stated length as automatic post spacing.
What Are Rally N Brace Farm Gates?
Rally N Brace Farm Gates are complete galvanised mesh-infill gates for rural fencing applications. They are not standalone N braces for reinforcing fence posts.
Rally specifies:
► 2400mm to 4200mm actual gate lengths
► 1170mm actual height
► Graduated mesh openings
► 5mm mesh wire
► Uniform 25NB pipe
► 25mm tube inside diameter
► 32mm tube outside diameter
► 2mm tube thickness
► Hot-dip galvanised tube inside & outside
► Mesh infill hot-dip galvanised before welding
The N Brace forms part of the gate construction. Select these products as complete farm gates rather than separate fencing-brace components.
Why Choose Rally N Brace Farm Gates?
Four widths cover wider rural gate requirements without changing the basic height or tube specification. Rally offers actual gate lengths of 2400mm, 3000mm, 3600mm & 4200mm.
Rally identifies the range for:
► Internal fence applications
► Boundary-fence applications
► Rural property entrances
► Livestock enclosures
► Suitable farm-access points
The graduated mesh arrangement provides another important point of difference. Instead of using one uniform aperture from bottom to top, the openings change through the lower, middle & upper sections of the gate.
Common Applications
An N Brace gate becomes particularly relevant where a wider rural opening aligns with one of Rally's four available lengths. Measure the entrance first, then consider how the gate will interact with the surrounding fence, posts, hinges & latch.
Suitable applications can include:
► Farm entrances
► Rural property access
► Boundary-fence openings
► Internal farm fencing
► Livestock enclosures
► Paddock access
► Property-maintenance access
The complete enclosure still determines suitability. Gate dimensions, mesh configuration, ground clearance, surrounding fencing & hardware should all be considered for the particular property requirement.
Rally N Brace Farm Gate Selection Guide
Width is the main size variable across this four-gate range.
|
Rally Model
|
Actual Length
|
Actual Height
|
Tube Thickness
|
|
MWFGNS2400
|
2400mm
|
1170mm
|
2mm
|
|
MWFGNS3000
|
3000mm
|
1170mm
|
2mm
|
|
MWFGNS3600
|
3600mm
|
1170mm
|
2mm
|
|
MWFGNS4200
|
4200mm
|
1170mm
|
2mm
|
Actual gate length should not automatically be treated as required post spacing. Allow for the intended hinges, latch arrangement, movement & installation clearances when planning the finished opening.
Understanding The Graduated Mesh
Look from the bottom of a Rally N Brace gate towards the top & the mesh openings progressively change. Rally specifies three sections rather than one uniform aperture across the full height.
The manufacturer lists:
► Bottom row: 30mm x 265mm openings with 5mm wire
► Middle 7 rows: 50mm x 265mm openings with 5mm wire
► Top 7 rows: 100mm x 265mm openings with 5mm wire
This graduated pattern is an important distinction when comparing farm gates. Assess the mesh arrangement together with the surrounding fence & livestock-containment requirements rather than comparing width alone.
Rally N Brace Gate Construction
The tubular frame remains consistent across all four Rally sizes. Each uses uniform 25NB pipe with defined inside diameter, outside diameter & wall thickness.
Construction details include:
► 25NB pipe
► 25mm inside diameter
► 32mm outside diameter
► 2mm tube wall
► 1170mm actual gate height
► Hot-dip galvanised tube inside & outside
► 5mm mesh wire
► Graduated mesh infill
Rally also distinguishes how the mesh itself is treated. The mesh infill is specified as hot-dip galvanised before welding.
Choose Your N Brace Gate Width
The four Rally sizes share the same height, tube specification & graduated mesh arrangement, so the opening becomes the main factor separating them.
► 2400mm: The shortest N Brace gate in the range for openings suited to a 2400mm actual gate length
► 3000mm: A wider option where the planned entrance suits a 3000mm actual gate
► 3600mm: Extends the available span for broader rural access requirements
► 4200mm: The widest current N Brace option in the Industrial Shed range
Choose around the finished entrance rather than simply moving up to the largest gate that will fit the fence line. Consider the usable passage required, hardware arrangement, supporting posts, ground conditions & gate swing before settling on a width.
How To Choose The Right N Brace Farm Gate?
Begin with the access requirement rather than the biggest gate available. A properly planned opening should provide the passage needed while working with the surrounding fence & hardware.
Check:
► Required usable opening
► Actual Rally gate length
► Gate height
► Hinge arrangement
► Latch arrangement
► Post positions
► Ground clearance
► Gate swing direction
► Surrounding fence alignment
► Vehicle or equipment access where relevant
Write the measurements down before ordering. An approximate opening can become a poor fit once hardware & operating clearances are introduced.
Rally N Brace Or I Brace Farm Gate?
Rally offers both N Brace & I Brace farm gates, but the two ranges solve different size & configuration requirements. Compare the actual specifications rather than choosing from the brace letter alone.
|
Feature
|
Rally N Brace
|
Rally I Brace
|
|
Current Industrial Shed lengths
|
2400mm–4200mm
|
830mm–4200mm
|
|
Actual height
|
1170mm
|
1170mm
|
|
Tube wall
|
2mm
|
1.5mm
|
|
Mesh arrangement
|
Graduated openings
|
200mm x 100mm uniform mesh
|
|
Mesh wire
|
5mm
|
5mm
|
|
Wider-gate bracing
|
N Brace construction
|
Centre bracing varies by width
|
Opening size can narrow the decision immediately. Buyers needing an actual gate length below 2400mm can compare the Rally I Brace Farm Gates, which extend down to 830mm.
Mesh arrangement is another clear difference. N Brace gates use graduated openings through the height while the I Brace range uses a uniform 200mm x 100mm mesh pattern.
Neither configuration should be chosen simply because one specification appears larger than another. Match the gate to the opening, surrounding fence, access requirement & intended enclosure.
Plan The Gate & Fence Together
A farm gate works as part of a boundary or internal fence rather than independently from it. Where the surrounding project also requires mesh, wire or associated fencing products, compare the wider Rally Fencing Supplies range around the same layout.
Plan:
► Gate position
► Fence direction
► Surrounding mesh or wire
► Supporting posts
► Ground changes
► Swing direction
► Access requirements
► Gate hardware
Drawing out the complete entrance can reveal conflicts before materials reach the property. Post position, gate movement & fence alignment should make sense together.
Galvanised Construction For Rural Gate Applications
Farm gates remain outdoors through changing conditions, making the specified finish an important part of product comparison. Rally hot-dip galvanises the 25NB tube inside & outside.
The mesh infill is specified as hot-dip galvanised before welding.
Regular inspection still matters on galvanised equipment. Check the gate, posts, hinges, latch & connection points as part of normal property maintenance.
N Brace Farm Gates For Rural & Commercial Buyers
Multiple gate openings across one property rarely share identical dimensions. Rural operators & maintenance teams can use the four Rally N Brace sizes where wider entrances align with the available gate lengths.
Relevant buyers can include:
► Farmers
► Rural property operators
► Fencing contractors
► Property-maintenance teams
► Land-management crews
► Commercial property operators
► Facilities teams managing rural sites
Recording installed gate information makes future maintenance easier. Keep the Rally model, actual gate length, opening dimensions & hardware details with property records where practical.
Expert Tips
Measure the usable opening before selecting the gate. Gate length & usable passage aren't necessarily identical.
Include the hardware in your measurements. Hinges & latches affect the finished arrangement.
Check the graduated mesh rather than assuming one aperture. The openings change from the bottom to the top.
Plan the swing before setting the posts. Ground, fence lines & nearby structures can restrict movement.
Treat 1170mm as the actual gate height. Ground clearance & installation position are separate considerations.
Compare N Brace & I Brace specifications directly. Available widths, mesh arrangement, tube wall & bracing configuration differ between the two Rally ranges.
Inspect existing posts before replacing a gate. A new gate doesn't correct unsuitable or damaged supports.
Record the model once installed. Exact identification simplifies future purchasing.