Fast Light-Duty Fixing with a Pre-Assembled Washer
When a thin fixture needs more bearing area than a plain nail provides, a pre-assembled washer keeps the fixing straightforward. ICCONS® Washered Drive Nails, commonly known as Mickey Pins, combine a 2.5 mm shank with an integrated washer for quick hammer installation across suitable light-duty construction work.
Five nail lengths—20, 25, 30, 40 & 50 mm—allow installers to match the fixing more closely to the material being secured & the receiving substrate. The range is intended for suitable low-load applications across concrete, brick, block, lightweight concrete & steel rather than connections requiring a specified structural anchoring system.
For nearby fixing options, compare Specialty Fasteners & Fixings, Anchors & Wall Plugs & Screws & Anchors.
What Are ICCONS® Washered Drive Nails?
ICCONS® Washered Drive Nails are pre-assembled single-nail fixings designed for fast, uncomplicated installation. Instead of handling a loose nail & washer separately, the washer is already positioned on the fixing.
ICCONS® places Mickey Pins within its Metal - Light Duty anchoring range & identifies quick, easy hammer installation as a key advantage.
The range uses a 2.5 mm shank across five lengths:
► MPW20 – 20 mm Washered Drive Nail
► MPW25 – 25 mm Washered Drive Nail
► MPW30 – 30 mm Washered Drive Nail
► MPW40 – 40 mm Washered Drive Nail
► MPW50 – 50 mm Washered Drive Nail
Length should be chosen around the fixture thickness, receiving material & required penetration rather than simply selecting the longest nail available. The completed fixing still needs to suit the substrate & light-duty nature of the application.
Why Choose ICCONS® Washered Drive Nails?
Install with a Hammer
Some everyday fixing tasks don't require gas, battery or powder-actuated equipment. Mickey Pins provide a straightforward hammer-driven method where the application & substrate are suitable for light-duty fastening.
This can make them practical for smaller fixing quantities, maintenance work, residential construction & other tasks where powered direct fastening isn't required.
Gain More Bearing Area at the Fixture
The integrated washer increases the contact area at the head of the fixing. This can be useful where thin material needs to be retained against the receiving surface without adding a separate loose washer during installation.
The additional bearing area doesn't convert the product into a heavy-duty or structural anchor.
Keep the Nail & Washer Together
Small loose components have a habit of separating once work moves around the site. The pre-assembled design keeps the washer with the nail from storage through to installation.
Where several nail lengths are carried alongside other consumables, Small Parts Organisers can help keep MPW20 through MPW50 stock separated.
Choose from Five Useful Lengths
Fixture thickness can change from one task to the next even when the fixing method remains suitable. ICCONS® provides 20, 25, 30, 40 & 50 mm Washered Drive Nails while retaining the same 2.5 mm shank width.
That progression gives installers a practical choice without treating one length as suitable for every job.
Common Applications
Light-Duty Concrete Fixing
Concrete surfaces often need small components or thin materials secured without introducing a heavier anchoring system. Washered Drive Nails provide an option where the substrate condition, fixture & required holding performance suit hammer-driven light-duty fastening.
Where a project calls for a rated mechanical or chemical anchor, use the fixing specified for that connection instead.
Brick & Block Work
Masonry isn't uniform from one project to another. ICCONS® identifies Mickey Pins for suitable brick, block & lightweight concrete applications within its light-duty range.
Check the actual base material before beginning repetitive installation, particularly on older buildings where masonry condition may vary.
Thin-Material Retention
A broader contact point can be valuable when the fixture itself is relatively thin. The pre-assembled washer spreads contact beyond the nail shank while eliminating the need to position a separate washer before each fixing is driven.
Fixture condition & required holding performance should still be considered before choosing the nail.
Suitable Steel Applications
ICCONS® also identifies steel among the applications for Washered Drive Nails. Steel thickness, hardness & the fixing requirement need to be appropriate for the selected nail rather than assuming every steel section can accept the same hammer-driven fixing.
If the substrate or connection falls outside the intended light-duty application, move to an appropriately specified fastening method.
Residential & General Construction
Simple installation is most valuable when the fixing remains appropriate for the task. Builders, maintenance crews & general construction teams can use Mickey Pins for suitable low-load work where hammer installation offers a practical alternative to more involved fastening equipment.
For a broader comparison of common fixing methods, read the Fastener Guide Bolts Screws Anchors.
Product Selection Guide
MPW part numbers make the length choice easy to identify once the application has been confirmed. Consider fixture thickness, substrate & required penetration before selecting between the five available sizes.
|
Part Number
|
Nail Length
|
Shank Width
|
Finish
|
Selection Consideration
|
|
MPW20
|
20 mm
|
2.5 mm
|
Zinc
|
Thinner fixtures & shorter fixing requirements
|
|
MPW25
|
25 mm
|
2.5 mm
|
Zinc
|
General light-duty fixing
|
|
MPW30
|
30 mm
|
2.5 mm
|
Zinc
|
Additional length where required
|
|
MPW40
|
40 mm
|
2.5 mm
|
Zinc
|
Thicker fixtures or greater required penetration
|
|
MPW50
|
50 mm
|
2.5 mm
|
Zinc
|
Longest MPW configuration in the range
|
Begin with Fixture Thickness
Only the section of nail extending beyond the fixture can penetrate the receiving material. Account for the material being retained when comparing 20, 25, 30, 40 & 50 mm lengths.
A nail selected without considering fixture thickness may provide less substrate penetration than expected.
Consider the Base Material
The same MPW30 fixing won't behave identically across concrete, brick, lightweight block & steel. Confirm that the receiving material is appropriate for a light-duty hammer-driven nail & inspect its condition before installation.
Damaged masonry, unusually hard material or unsuitable steel may call for another fixing method.
Don't Equate Additional Length with Additional Capacity
Moving from MPW20 to MPW50 changes nail length, not the fundamental purpose of the product. Holding performance also depends on the substrate, fixture, penetration & installation conditions.
Where the connection has defined performance requirements, select the fastening system from those requirements rather than choosing a longer Mickey Pin.
Washered Drive Nail or Another Anchor?
Ask what the finished fixing is expected to support. Mickey Pins suit appropriate light-duty hammer fixing, while mechanical anchors, chemical anchors & other systems address different substrates, loads & installation requirements.
For other threaded & general fastening hardware used across construction work, browse Bolts & Fasteners.
Expert Tips
Trial the Fixing Before Repeating It Across the Job
A test installation can expose an unsuitable substrate before dozens of fixings have been attempted. Confirm that the chosen nail drives correctly, seats as intended & suits the receiving material before commencing repetitive work.
This is especially useful during renovation & maintenance work where substrate condition may be uncertain.
Treat the Washer as a Fixture-Retention Feature
The washer provides additional contact area where the nail meets the fixture. It shouldn't be interpreted as evidence that the connection can carry structural or safety-critical loads.
Where a connection requires documented anchor performance, use the specified fastening system.
Separate MPW Sizes Before Work Starts
Twenty & twenty-five millimetre fixings are easier to distinguish in labelled storage than from a mixed handful on site. Keep MPW20, MPW25, MPW30, MPW40 & MPW50 separated so crews can identify the required length without repeatedly measuring individual nails.
Clear separation also makes remaining stock easier to monitor.
Check the Material Being Retained
The substrate isn't the only surface affected during installation. Thin, brittle or easily marked fixtures may respond differently to hammer impact & washer pressure.
Make sure the washer seats appropriately without unnecessarily damaging the material.
For practical site preparation before busier work periods, see Spring Jobsite Prep Getting Your Gear Ready.
Don't Confuse Mickey Pins with Powder-Actuated Washered Pins
A pre-assembled washer doesn't mean the products share the same installation system. ICCONS® Mickey Pins are hammer-driven light-duty nails, while PX washered drive pins are consumables for compatible powder-actuated fastening equipment.
Keep these product families separate during specification, ordering & site preparation.
Reconsider the Installation Method When Quantity Increases
A practical method for twenty fixing points may become inefficient across several hundred. If the project involves extensive repetitive fastening, assess whether an appropriate direct-fastening system better suits the substrate, fixture & required installation volume.
Speed should never override fixing suitability.
Select the Connection Before the Tool
A familiar hammer shouldn't determine which fixing is used. Start with the fixture, substrate & required holding performance, then choose the installation method appropriate to that connection.
For related striking equipment used across general construction & maintenance, explore Hand Tools.
For further practical guidance on fastening selection, read Why Good Fasteners Matter More Than the Tool You Drive Them With.