Through-Fix Frames & Profiles Into Concrete & Masonry
Frames, profiles & substructures need a fixing that suits both the component in front & the masonry behind it. ICCONS® | Nylon Frame Fixing Screws include the Friulsider FM-X5 family of pre-assembled nylon frame fixings for light-duty, non-structural fastening into compatible concrete & masonry base materials.
The FM-X5 combines a Ø10 mm nylon plug with a pre-assembled screw, allowing installation through a positioned fixture into the prepared substrate. Applications include façade & roofing substructures, profiles, insulation fixing & other suitable frame connections. For adjoining installation requirements, compare Anchors & Wall Plugs, Concrete Cutting & Drilling Tools or Drill Accessories.
Across the documented FM-X5 family, available characteristics include:
► Ø10 mm frame-fixing format
► 70 mm minimum anchor embedment across standard documented configurations
► 85 mm to 160 mm documented lengths
► Pre-assembled screw & nylon plug
► Multi-expansion plug geometry
► Countersunk & hex-head configurations
► T40 anti-intrusion option
► FM-X5 TOP higher-performance configuration
► Zinc, galvanised & selected 316 stainless steel options depending on variant
► Applications across compatible concrete & masonry base materials
What Are ICCONS® Nylon Frame Fixing Screws?
FM-X5 frame fixings combine a screw & nylon plug into one pre-assembled fastening system.
A correctly sized hole is prepared through the fixture & into the compatible base material. The fixing passes through the component before the screw is tightened to activate the nylon plug.
This through-fixing method can suit:
► Façade substructures
► Roofing substructures
► Profiles
► Insulation fixing
► Suitable frame installations
Because the fixture can remain in position during installation, set-out can be maintained while the fixing points are prepared.
The exact FM-X5 configuration still needs to correspond with the substrate, fixture thickness, head requirement & project conditions.
Multi-Expansion Geometry Works Across Compatible Masonry Types
Concrete, brick & aerated masonry behave differently when a fixing expands inside the prepared hole.
ICCONS describes FM-X5 with multi-expansion plug geometry, including differentiated expansion towards the plug tip.
Documented compatible base materials across the family include:
► Concrete
► Stone
► Solid brick
► Hollow brick
► Aerated concrete
FM-X5 TOP documentation also identifies solid & hollow block applications.
Use the technical information for the exact FM-X5 variant when confirming suitability for the material being fixed into.
Select Length From Fixture Thickness & Required Embedment
The part of the fixing passing through the frame cannot also provide embedment in the base material.
For standard documented FM-X5 countersunk & hex configurations, the relationship is:
|
Fixing Length
|
Minimum Embedment
|
Maximum Fixture Thickness
|
|
85 mm
|
70 mm
|
15 mm
|
|
100 mm
|
70 mm
|
30 mm
|
|
115 mm
|
70 mm
|
45 mm
|
|
135 mm
|
70 mm
|
65 mm
|
|
160 mm
|
70 mm
|
90 mm
|
Measure the complete material thickness between the fixing head & masonry surface.
Packing or other intermediate materials can increase the distance the fixing needs to pass through before reaching its required embedment.
Countersunk Heads Suit Low-Profile Connections
A countersunk fixing can provide a neater surface where the fixture is designed to receive that head shape.
ICCONS documents FM-X5 countersunk versions with a CSK/TX40 head.
This configuration can be considered where:
► Minimal head projection is preferred
► The fixture accepts a countersunk head
► TX40 installation suits the work
► The selected length provides the required embedment
The head should seat against a compatible surface rather than being forced into material that has not been prepared for a countersunk connection.
For a broader explanation of fixing families & their different installation methods, read the Fastener Guide Bolts Screws Anchors.
Hex-Head FM-X5 Gives the Installer a Different Seating Option
Some profiles & substructures are better suited to a fixing head that remains accessible above the fixture.
Standard FM-X5 hex-head versions retain the documented Ø10 mm hole diameter & 70 mm minimum embedment across their applicable length range while providing a different driving arrangement from the countersunk models.
A hex head may suit work where:
► Head access remains available
► The fixture accepts a projecting head
► The driving arrangement suits installation access
► Countersinking is unnecessary
Choose the head configuration around the actual component rather than treating countersunk & hex versions as interchangeable.
Anti-Intrusion Heads Suit More Exposed Fixing Points
Where the completed fixing remains accessible, resistance to casual removal may become part of product selection.
The FM-X5 Safety configuration uses a T40 anti-intrusion head.
The documented 10 x 85 mm configuration includes:
► Ø10 mm drill diameter
► 70 mm embedment
► 15 mm maximum fixture thickness
► Anti-intrusion/TX40 head
► Zinc or selected 316 stainless steel options
Make sure the corresponding installation drive is available before the fixing work begins.
FM-X5 TOP Is a Separate Higher-Performance Configuration
Variants within the same fixing family can differ in more than head shape.
FM-X5 TOP is documented with:
► PA 6.6 nylon plug
► Multi-expansion geometry
► Anti-rotation barbs
► Pre-assembled screw
► Increased screw diameter
► Asymmetrical thread
► Collared hex head with internal TX40 drive
ICCONS positions FM-X5 TOP as a higher-performance version within the frame-fixing family.
Specify the actual variant required rather than substituting standard countersunk, hex, Safety & TOP configurations solely because their overall dimensions appear similar.
Start With the Documented Ø10 mm Hole
Correct frame fixing begins below the surface with the hole prepared for the plug.
Standard documented FM-X5 countersunk & hex configurations specify a Ø10 mm drill diameter.
Before drilling:
► Identify the exact fixing
► Confirm the base material
► Establish the required depth
► Allow for the nominated embedment
► Keep the drilling position aligned
► Follow the applicable installation instructions
Suitable Hammer Drills can support masonry drilling where the tool, operating mode & bit suit the material.
Avoid enlarging the hole through unnecessary drill movement.
Through-Fixing Helps Preserve Frame Set-Out
Once a frame or profile has been positioned correctly, unnecessary movement during drilling & fastening can undo careful preparation.
Where the installation permits, a practical sequence is:
► Position the component
► Confirm level, plumb or alignment
► Mark the fixing locations
► Drill through the fixture into the substrate
► Prepare the hole as required
► Insert the pre-assembled fixing
► Tighten with the appropriate drive
► Recheck the finished position
This approach can be particularly useful across repetitive profile & substructure work.
For wider preparation of site tools & consumables, Spring Jobsite Prep Getting Your Gear Ready provides practical jobsite guidance.
Hollow Brick Needs Controlled Drilling
The drill can move from solid material into a cavity within a single hole when working with hollow masonry.
FM-X5 is documented for compatible hollow-brick applications, but hole quality still matters.
Avoid:
► Excessive drilling pressure
► Unnecessary enlargement
► Damaging masonry webs
► Using an incorrect drill diameter
► Assuming every brick behaves identically
Prepare the hole according to the fixing requirements & characteristics of the masonry being drilled.
Aerated Concrete Requires Its Own Installation Consideration
Lower-density base materials should not inherit installation assumptions from ordinary concrete.
ICCONS provides FM-X5 information covering aerated concrete applications.
For this substrate, establish:
► Exact fixing configuration
► Hole-preparation requirements
► Embedment
► Fixture thickness
► Installation method
► Applicable technical information
Do not transfer capacities or installation assumptions between different base materials without supporting documentation.
Match Screw Material & Finish to the Required Configuration
Not every FM-X5 variant uses the same screw material or protective finish.
Depending on configuration, the documented family includes zinc, galvanised & selected 316 stainless steel options.
Before ordering, consider:
► Installation environment
► Required screw material or finish
► Head style
► Fixing length
► Base material
► Project specification
Confirm the exact product rather than assuming that a finish available on one FM-X5 version applies across the complete range.
Set the Frame Before Final Tightening
A frame fixing is there to secure the chosen position, not establish alignment by force.
Before tightening, check:
► Level
► Plumb
► Alignment
► Required clearances
► Packing locations
► Fixing position
If packers sit behind the frame or profile, make sure they remain correctly positioned as the fixing seats.
Movement during tightening should be addressed rather than accepted as part of the installation.
Stop When the Fixing Is Correctly Seated
Additional torque after seating can damage the drive, fixture or fixing arrangement rather than improve it.
Use the drive corresponding with the selected head & follow the applicable installation requirements.
Pay attention to:
► Head seating
► Fixture movement
► Plug rotation
► Drive-recess condition
► Distortion around the fixing point
Unexpected behaviour can indicate an issue with the hole, substrate, fixing selection or installation.
For further practical context, read Why Good Fasteners Matter More Than the Tool You Drive Them With.
Keep Light-Duty Frame Fixing Separate From Structural Anchoring
FM-X5 is documented as a plastic anchor for light-duty, non-structural applications.
That distinction becomes important where the same project also contains structural concrete connections.
Do not substitute a nylon frame fixing for an engineered anchor simply because both products can be installed into concrete or masonry.
Connections involving structural requirements should use the fixing system nominated for that duty.
For adjoining structural hardware, browse Structural Fasteners & Bolts.
Treat Fire Classification in Its Documented Application
FM-X5 fire-performance information needs to remain connected to the application for which it is documented.
ICCONS technical information identifies an F90 fire resistance classification with the fire rating stated as valid for façade applications only.
Where fire performance forms part of the project requirements, confirm:
► Exact FM-X5 variant
► Base material
► Façade application
► Installation arrangement
► Current supporting documentation
Do not extend a documented façade classification to unrelated installations without supporting information.
Plan Repetitive Frame Fixing Before Drilling Starts
A long run of profiles becomes easier to manage when fixing lengths, head styles & drilling equipment have already been matched to the work.
Before starting repetitive installation, establish:
► Substrate
► Fixture thickness
► FM-X5 length
► Head configuration
► Required finish
► Drill bit
► Driving equipment
► Set-out positions
For associated threaded fastening requirements elsewhere in the assembly, Bolts & Fasteners provides a broader hardware range.
Keeping the fixing configuration consistent with the actual assembly reduces unnecessary changes once installation is underway.