► ICCONS® | Drilling Power Tool Accessories

Purpose-Matched Bits, Sockets & Drilling Attachments When a screw recess strips, a socket cannot reach or the drill body will not fit into the available space, the accessory becomes critical to getting the job completed properly. ICCONS® | Drilling Power Tool Accessories brings together FastDrive insert & power bits, nut...

Purpose-Matched Bits, Sockets & Drilling Attachments

When a screw recess strips, a socket cannot reach or the drill body will not fit into the available space, the accessory becomes critical to getting the job completed properly. ICCONS® | Drilling Power Tool Accessories brings together FastDrive insert & power bits, nut setters, bit holders, impact sockets, countersinking tools, right-angle attachments, tile-drilling equipment & Ratio Quick coring components for professional drilling, fastening & installation work. Builders, carpenters, electricians, plumbers, maintenance crews & fit-out contractors can choose equipment around the connection, substrate & access conditions encountered on site.

Different tasks call for distinctly different accessories. Driving a PH2 screw, installing a hex-head fixing, reaching a fastener beside cabinetry, countersinking decking, preparing fibre cement & coring a masonry penetration each place different demands on the equipment. Establish the operation first then match the drive profile, connection, material & required reach.

Installing hardware after drilling? Browse Screws & Anchors for fixing options,  Drill Accessories for wider drilling equipment or Structural Fasteners & Bolts when the work moves into larger fastening hardware.

► FastDrive insert & power bits
► Impact & standard nut setters
► Magnetic quick-release bit holders
► Standard, deep, Hex & Torx impact sockets
► 90° right-angle drilling attachment
► Timber & fibre-cement countersinking equipment
► Cera Expert tile-drilling tools
► Ratio Quick masonry coring components
► Bit kits & replacement pilot bits

Choose by the Contact Point

Every accessory in this category has a connection where correct fit matters.

For a driver bit, that point is the screw recess.

For a nut setter, it is the outside of the hex head.

For an impact socket, both the fastener interface & wrench drive need to correspond.

For a countersinking tool, the screw gauge & material become important.

For Ratio Quick, the required core diameter & rotary-hammer connection need to work together.

Installation Task

ICCONS Accessory Family

Check First

Drive recessed screws

FastDrive Insert / Power Bits

Drive profile & size

Install hex-head screws

FastDrive Nut Setters

Hex-head dimension

Retain insert bits

FastDrive Bit Holder

¼" bit compatibility

Install larger anchors

Impact Sockets

Socket size & drive

Reach restricted screws

90° Drill Attachment

Access & bit compatibility

Countersink timber

Smart-Bit / Better Bit

Screw gauge & material

Prepare fibre cement

Better Bit / Smart-Bit

Board & fixing

Drill suitable tile

Cera Expert

Tile & required hole

Core masonry

Ratio Quick

Diameter & SDS system

Checking these details before ordering helps prevent incompatible accessories arriving on site.

FastDrive Selection Starts Inside the Screw Head

Phillips, Square, Hex, Pozi & Torx profiles may all appear in the same toolbox but their working geometry is different.

ICCONS FastDrive includes insert & power bits across multiple profiles for compatible screws & fasteners.

Check:

► Drive profile
► Drive size
► Required bit length
► Insert or power-bit format
► Impact or standard application
► Access around the fixing

ICCONS' standard power-bit range also uses colour identification across documented profiles, including green for Hex, red for Phillips, blue for Square & white for Pozi.

Colour can make frequently used bits easier to identify but the fastener recess remains the specification that matters.

A driver tip that looks close should not replace the correct profile.

For practical guidance on the relationship between tooling & fixing quality, read Why Good Fasteners Matter More Than the Tool You Drive Them With.

Impact Driving Places Different Demands on the Bit

Repeated rotational impacts create a different working environment from conventional screw driving.

ICCONS separates FastDrive impact & standard accessory families accordingly.

Impact insert & power bits incorporate features intended for impact-driving applications, including torsion zones across applicable products. Standard power bits are available for compatible conventional driving work.

Before fitting a bit, check:

► Impact driver or conventional drill driver
► Accessory suitability for the tool
► Correct drive profile
► Required reach
► Condition of the bit

Correct engagement at the screw & appropriate compatibility with the tool both contribute to a reliable setup.

Nut Setters Make Hex-Head Selection Straightforward

External hex-head screws move the working interface from a recess inside the fastener to the dimensions around its head.

ICCONS FastDrive includes impact, pressure-fit & standard nut-setter configurations.

Documented colour identification includes:

► Red – ¼"
► Yellow – 5/16"
► Blue – 3/8"

This can make frequently used sizes quicker to identify during installation work.

Always confirm that the setter seats correctly over the fastener before driving.

Colour is an identification aid while the actual fastener-head dimension determines the required size.

Tight Access Is Where a Right-Angle Attachment Becomes Useful

Some fasteners are positioned correctly but leave too little room to align the drill body directly behind them.

ICCONS' 90° right-angle drill attachment provides a quick-release bit-holder arrangement for difficult-to-reach screws using compatible insert & power bits.

Applications can include:

► Cabinetry
► Framing intersections
► Tight service spaces
► Restricted maintenance areas
► Fixtures close to walls
► Equipment with obstructed access

A right-angle attachment changes the approach angle without changing the drive profile required by the screw.

Fit the correct driver bit first then use the attachment where physical access prevents straight-line driving.

Bit Holders Keep Insert Bits Ready for Fast Changes

Fit-out & installation work can move through several fastener profiles before a task is finished.

ICCONS FastDrive magnetic bit holders provide the interface for compatible ¼" insert bits, with quick-release options available within the range.

The setup can be considered as four separate components:

► Power tool provides the drive
► Holder retains the insert bit
► Insert bit engages the screw
► Screw completes the fastening connection

When retention becomes unreliable, inspect the holder as well as the insert bit.

When slipping occurs at the screw recess, check drive profile, size & bit condition.

Identifying which component has changed helps avoid replacing serviceable equipment unnecessarily.

Impact Sockets Step Up for Larger Fixing Work

Mechanical anchors & larger fasteners often require a different interface from the small ¼" accessories used for screw driving.

ICCONS documents impact sockets for compatible ½" impact wrenches across anchor & fixing installation.

The range includes:

► Standard impact sockets
► Deep impact sockets
► Hex impact sockets
► Torx impact sockets
► Impact socket adaptors

ICCONS documents its ½" socket range around anchor installation spanning approximately 8 mm to 43 mm.

For related mechanical fixing hardware, browse Anchor Bolts.

Select socket size from the fixing being installed rather than simply from the capacity of the impact wrench.

Standard & Deep Sockets Solve Different Access Requirements

Projecting thread or unusual connection geometry can prevent a standard socket from reaching the working surface.

A standard socket remains practical where normal access is available.

A deep socket provides additional internal clearance where the fixing arrangement genuinely requires it.

Check:

► Fastener or nut size
► Projecting thread
► Socket profile
► Drive size
► Available access
► Fixing installation instructions

For manually operated fastening equipment where appropriate, browse Ratchets & Spanners.

Choose additional depth to solve a defined clearance problem rather than treating it as the default socket format.

Decking Preparation Starts Before the Screw Goes In

The finished appearance of a deck can be influenced by the hole prepared before the screw reaches the timber.

ICCONS' Smart-Bit & The Better Bit ranges provide purpose-designed pre-drilling & countersinking options for timber applications.

The Better Bit includes adjustable countersink configurations for documented screw gauges while Smart-Bit provides pilot-hole & countersinking functionality.

Applications include:

► Deck construction
► Hardwood installation
► Softwood installation
► Joinery
► Timber fixtures
► General woodworking

Pre-drilling can assist where splitting is a concern while controlled countersinking prepares the surface around the screw head.

Careful preparation gives the fixing a properly formed starting point rather than relying on the screw to create the entire opening.

Replace a Worn Pilot Bit Without Discarding Serviceable Components

Regular decking & woodworking can wear the pilot drill before the surrounding countersinking assembly needs replacement.

ICCONS offers Smart-Bit replacement pilot drill bits across several documented screw-gauge configurations.

Replacement options cover sizes associated with 7G, 8G, 10G, 12G & 14G Smart-Bit tools, with drill diameters varying according to the corresponding setup.

Before selecting a replacement:

► Identify the Smart-Bit tool
► Confirm screw gauge
► Match the replacement specification
► Inspect the remaining countersink assembly

Replacing the appropriate wear component keeps serviceable parts of the setup in use.

Fibre Cement Calls for Material-Specific Preparation

Fibre-cement board behaves differently from timber when a fixing hole & countersink are being prepared.

ICCONS provides dedicated Smart-Bit & Better Bit solutions for fibre-cement applications.

The Better Bit for Fibre Cement uses a tungsten-carbide-tipped drill & countersink with an adjustable control arrangement designed around pre-drilling & countersinking fibre-cement board.

ICCONS also documents Smart-Bit tooling for suitable fibre-cement applications.

Before preparing the sheet:

► Confirm board type
► Check thickness
► Verify screw gauge
► Follow board-manufacturer requirements
► Establish countersink depth
► Keep the tool square to the surface

Selecting equipment designed around the material helps produce a more controlled preparation process.

Tile Drilling Requires Care at the Finished Surface

Bathrooms, kitchens & service areas can place the drilling point directly through a finished tile where an incorrect accessory can damage more than the hole itself.

ICCONS includes Cera Expert tile-drilling products within its drilling-accessory range.

Before drilling:

► Identify the tile material
► Confirm hole diameter
► Establish what sits behind the tile
► Check the appropriate drilling method
► Mark the position accurately
► Select tooling suited to the surface

For accurate positioning before drilling finished materials, browse Measuring & Layout Tools.

Check both the visible surface & the substrate behind it before committing the bit to the marked position.

Ratio Quick Handles Larger Openings Through Suitable Masonry

Plumbing, electrical & other service work can require an opening considerably larger than a conventional drill-bit hole.

ICCONS Ratio Quick Core Bits are documented in:

► 50 mm
► 65 mm
► 80 mm

They are intended for suitable soft concrete & masonry applications.

The supporting system includes:

► Ratio Quick Core Pilot Bit
► Ratio Quick Adaptor SDS Plus
► Ratio Quick Adaptor SDS Max

For wider concrete & masonry drilling equipment, browse Concrete Cutting & Drilling Tools.

Determine the penetration diameter first then match the supporting components to the rotary-hammer system being used.

Ratio Quick & Diamond Coring Serve Different Drilling Setups

Larger holes can be produced with different equipment systems depending on the substrate, diameter & work being undertaken.

Ratio Quick is an ICCONS core-bit system for compatible soft concrete & masonry applications using SDS Plus or SDS Max adaptors.

Dedicated diamond coring can involve different machines, core barrels, stands, water-management equipment & supporting accessories.

Requirement

Ratio Quick

Diamond Coring Setup

Documented use

Soft concrete & masonry

Dedicated diamond drilling

Connection

SDS Plus / SDS Max adaptor

Depends on coring system

Ratio Quick diameters

50, 65 & 80 mm

Depends on selected system

Equipment focus

Core, pilot & rotary-hammer adaptor

Core drill, barrel & supporting equipment

Choose between systems according to the actual penetration & equipment requirements of the job.

Bit Kits Work Best When Their Profiles Match Everyday Fasteners

An organised assortment becomes useful when it contains the drive profiles the crew repeatedly encounters.

ICCONS FastDrive includes multi-piece bit kits alongside BITZ storage options.

A documented 10-piece impact kit combines impact insert bits across PH2, SQ2 & HX5 profiles with a bit holder.

These kits can suit:

► Maintenance vehicles
► Builder toolboxes
► Installation crews
► Fit-out teams
► Workshop benches
► Service technicians

For broader grouped tooling, browse Tool Sets.

Compare the included profiles with the fasteners used regularly rather than choosing from piece count alone.

Practical Checks Before Drilling or Driving

Small accessories transfer the tool's output directly into the fixing or material, making condition & compatibility worth checking before work starts.

► Confirm the recess. Similar-looking drive profiles are not interchangeable.
► Separate impact from standard use. Match the accessory to the operating environment.
► Inspect the holder when retention changes. The insert bit may not be causing the problem.
► Choose socket depth deliberately. Deep sockets solve specific clearance requirements.
► Check pilot drills before decking work. Worn or damaged Smart-Bit pilot components can be replaced where compatible.
► Treat fibre cement separately from timber. Select preparation equipment around the board being installed.
► Check the hidden substrate before tile drilling. The finished surface is only one part of the drilling task.
► Match Ratio Quick adaptors to the rotary hammer. SDS Plus & SDS Max use their respective compatible adaptors.
► Use right-angle equipment to overcome restricted access. The fastener still requires the correct driver profile.

For practical preparation before demanding periods on site, read Spring Jobsite Prep Getting Your Gear Ready.

Why Buy ICCONS® Drilling Power Tool Accessories From Industrial Shed?

The right accessory needs to work with the tool, fixing or material & the conditions surrounding the installation.

Industrial Shed supports Australian builders, contractors, maintenance crews, installers & workshops across drilling equipment, fastening hardware & supporting trade tools.

When a drill, driver or impact wrench needs assessment beyond replacing a worn accessory, Power Tool Repairs & Diagnostics provides a dedicated equipment-support pathway.

For crews managing repeat tooling requirements across workshops & active sites, on -site & workshop Services provides broader operational support.

For further reading on maintaining dependable equipment, see A tool is not just a tool. It’s a promise..

Match the Accessory to the Work in Front of You

From a recessed screw in a tight corner to an anchor socket, timber countersink or masonry service penetration, each task places a different requirement on the accessory fitted to the tool.

Check the interface, material, equipment compatibility & access conditions before work begins then replace worn components when they can no longer perform their intended role.

Choose ICCONS drilling power tool accessories for the specific fastening, preparation, access & drilling tasks your crew handles on site or in the workshop.

Frequently Asked Questions

Which ICCONS FastDrive bit should I use for a particular screw?

Identify the screw's drive profile & size. ICCONS FastDrive covers Phillips, Hex, Square, Pozi & Torx options across suitable insert, power, impact & standard configurations.

What can I use when there isn't enough room to position the drill directly behind a screw?

ICCONS offers a 90° right-angle drill attachment with a quick-release bit holder for compatible insert & power bits where straight tool access is restricted.

Can a worn Smart-Bit pilot drill be replaced separately?

Yes. ICCONS documents replacement pilot-bit packs for compatible Smart-Bit gauges. Match the replacement component to the exact Smart-Bit configuration.

When is a deep impact socket useful?

A deep socket provides additional internal clearance where projecting thread or fixing geometry prevents a standard socket from engaging correctly.

Does ICCONS offer accessories for drilling hard tiles?

Yes. ICCONS includes Cera Expert tile-drilling products within its drilling-accessory range. Select the appropriate equipment according to the tile material & required hole.

Is Ratio Quick the same as diamond coring?

No. Ratio Quick is an ICCONS system for compatible soft concrete & masonry applications with documented 50 mm, 65 mm & 80 mm core bits plus SDS Plus & SDS Max adaptors. Dedicated diamond coring uses a different equipment arrangement.

Brands

► ICCONS® | Drilling Power Tool Accessories

Purpose-Matched Bits, Sockets & Drilling Attachments

When a screw recess strips, a socket cannot reach or the drill body will not fit into the available space, the accessory becomes critical to getting the job completed properly. ICCONS® | Drilling Power Tool Accessories brings together FastDrive insert & power bits, nut setters, bit holders, impact sockets, countersinking tools, right-angle attachments, tile-drilling equipment & Ratio Quick coring components for professional drilling, fastening & installation work. Builders, carpenters, electricians, plumbers, maintenance crews & fit-out contractors can choose equipment around the connection, substrate & access conditions encountered on site.

Different tasks call for distinctly different accessories. Driving a PH2 screw, installing a hex-head fixing, reaching a fastener beside cabinetry, countersinking decking, preparing fibre cement & coring a masonry penetration each place different demands on the equipment. Establish the operation first then match the drive profile, connection, material & required reach.

Installing hardware after drilling? Browse Screws & Anchors for fixing options,  Drill Accessories for wider drilling equipment or Structural Fasteners & Bolts when the work moves into larger fastening hardware.

► FastDrive insert & power bits
► Impact & standard nut setters
► Magnetic quick-release bit holders
► Standard, deep, Hex & Torx impact sockets
► 90° right-angle drilling attachment
► Timber & fibre-cement countersinking equipment
► Cera Expert tile-drilling tools
► Ratio Quick masonry coring components
► Bit kits & replacement pilot bits

Choose by the Contact Point

Every accessory in this category has a connection where correct fit matters.

For a driver bit, that point is the screw recess.

For a nut setter, it is the outside of the hex head.

For an impact socket, both the fastener interface & wrench drive need to correspond.

For a countersinking tool, the screw gauge & material become important.

For Ratio Quick, the required core diameter & rotary-hammer connection need to work together.

Installation Task

ICCONS Accessory Family

Check First

Drive recessed screws

FastDrive Insert / Power Bits

Drive profile & size

Install hex-head screws

FastDrive Nut Setters

Hex-head dimension

Retain insert bits

FastDrive Bit Holder

¼" bit compatibility

Install larger anchors

Impact Sockets

Socket size & drive

Reach restricted screws

90° Drill Attachment

Access & bit compatibility

Countersink timber

Smart-Bit / Better Bit

Screw gauge & material

Prepare fibre cement

Better Bit / Smart-Bit

Board & fixing

Drill suitable tile

Cera Expert

Tile & required hole

Core masonry

Ratio Quick

Diameter & SDS system

Checking these details before ordering helps prevent incompatible accessories arriving on site.

FastDrive Selection Starts Inside the Screw Head

Phillips, Square, Hex, Pozi & Torx profiles may all appear in the same toolbox but their working geometry is different.

ICCONS FastDrive includes insert & power bits across multiple profiles for compatible screws & fasteners.

Check:

► Drive profile
► Drive size
► Required bit length
► Insert or power-bit format
► Impact or standard application
► Access around the fixing

ICCONS' standard power-bit range also uses colour identification across documented profiles, including green for Hex, red for Phillips, blue for Square & white for Pozi.

Colour can make frequently used bits easier to identify but the fastener recess remains the specification that matters.

A driver tip that looks close should not replace the correct profile.

For practical guidance on the relationship between tooling & fixing quality, read Why Good Fasteners Matter More Than the Tool You Drive Them With.

Impact Driving Places Different Demands on the Bit

Repeated rotational impacts create a different working environment from conventional screw driving.

ICCONS separates FastDrive impact & standard accessory families accordingly.

Impact insert & power bits incorporate features intended for impact-driving applications, including torsion zones across applicable products. Standard power bits are available for compatible conventional driving work.

Before fitting a bit, check:

► Impact driver or conventional drill driver
► Accessory suitability for the tool
► Correct drive profile
► Required reach
► Condition of the bit

Correct engagement at the screw & appropriate compatibility with the tool both contribute to a reliable setup.

Nut Setters Make Hex-Head Selection Straightforward

External hex-head screws move the working interface from a recess inside the fastener to the dimensions around its head.

ICCONS FastDrive includes impact, pressure-fit & standard nut-setter configurations.

Documented colour identification includes:

► Red – ¼"
► Yellow – 5/16"
► Blue – 3/8"

This can make frequently used sizes quicker to identify during installation work.

Always confirm that the setter seats correctly over the fastener before driving.

Colour is an identification aid while the actual fastener-head dimension determines the required size.

Tight Access Is Where a Right-Angle Attachment Becomes Useful

Some fasteners are positioned correctly but leave too little room to align the drill body directly behind them.

ICCONS' 90° right-angle drill attachment provides a quick-release bit-holder arrangement for difficult-to-reach screws using compatible insert & power bits.

Applications can include:

► Cabinetry
► Framing intersections
► Tight service spaces
► Restricted maintenance areas
► Fixtures close to walls
► Equipment with obstructed access

A right-angle attachment changes the approach angle without changing the drive profile required by the screw.

Fit the correct driver bit first then use the attachment where physical access prevents straight-line driving.

Bit Holders Keep Insert Bits Ready for Fast Changes

Fit-out & installation work can move through several fastener profiles before a task is finished.

ICCONS FastDrive magnetic bit holders provide the interface for compatible ¼" insert bits, with quick-release options available within the range.

The setup can be considered as four separate components:

► Power tool provides the drive
► Holder retains the insert bit
► Insert bit engages the screw
► Screw completes the fastening connection

When retention becomes unreliable, inspect the holder as well as the insert bit.

When slipping occurs at the screw recess, check drive profile, size & bit condition.

Identifying which component has changed helps avoid replacing serviceable equipment unnecessarily.

Impact Sockets Step Up for Larger Fixing Work

Mechanical anchors & larger fasteners often require a different interface from the small ¼" accessories used for screw driving.

ICCONS documents impact sockets for compatible ½" impact wrenches across anchor & fixing installation.

The range includes:

► Standard impact sockets
► Deep impact sockets
► Hex impact sockets
► Torx impact sockets
► Impact socket adaptors

ICCONS documents its ½" socket range around anchor installation spanning approximately 8 mm to 43 mm.

For related mechanical fixing hardware, browse Anchor Bolts.

Select socket size from the fixing being installed rather than simply from the capacity of the impact wrench.

Standard & Deep Sockets Solve Different Access Requirements

Projecting thread or unusual connection geometry can prevent a standard socket from reaching the working surface.

A standard socket remains practical where normal access is available.

A deep socket provides additional internal clearance where the fixing arrangement genuinely requires it.

Check:

► Fastener or nut size
► Projecting thread
► Socket profile
► Drive size
► Available access
► Fixing installation instructions

For manually operated fastening equipment where appropriate, browse Ratchets & Spanners.

Choose additional depth to solve a defined clearance problem rather than treating it as the default socket format.

Decking Preparation Starts Before the Screw Goes In

The finished appearance of a deck can be influenced by the hole prepared before the screw reaches the timber.

ICCONS' Smart-Bit & The Better Bit ranges provide purpose-designed pre-drilling & countersinking options for timber applications.

The Better Bit includes adjustable countersink configurations for documented screw gauges while Smart-Bit provides pilot-hole & countersinking functionality.

Applications include:

► Deck construction
► Hardwood installation
► Softwood installation
► Joinery
► Timber fixtures
► General woodworking

Pre-drilling can assist where splitting is a concern while controlled countersinking prepares the surface around the screw head.

Careful preparation gives the fixing a properly formed starting point rather than relying on the screw to create the entire opening.

Replace a Worn Pilot Bit Without Discarding Serviceable Components

Regular decking & woodworking can wear the pilot drill before the surrounding countersinking assembly needs replacement.

ICCONS offers Smart-Bit replacement pilot drill bits across several documented screw-gauge configurations.

Replacement options cover sizes associated with 7G, 8G, 10G, 12G & 14G Smart-Bit tools, with drill diameters varying according to the corresponding setup.

Before selecting a replacement:

► Identify the Smart-Bit tool
► Confirm screw gauge
► Match the replacement specification
► Inspect the remaining countersink assembly

Replacing the appropriate wear component keeps serviceable parts of the setup in use.

Fibre Cement Calls for Material-Specific Preparation

Fibre-cement board behaves differently from timber when a fixing hole & countersink are being prepared.

ICCONS provides dedicated Smart-Bit & Better Bit solutions for fibre-cement applications.

The Better Bit for Fibre Cement uses a tungsten-carbide-tipped drill & countersink with an adjustable control arrangement designed around pre-drilling & countersinking fibre-cement board.

ICCONS also documents Smart-Bit tooling for suitable fibre-cement applications.

Before preparing the sheet:

► Confirm board type
► Check thickness
► Verify screw gauge
► Follow board-manufacturer requirements
► Establish countersink depth
► Keep the tool square to the surface

Selecting equipment designed around the material helps produce a more controlled preparation process.

Tile Drilling Requires Care at the Finished Surface

Bathrooms, kitchens & service areas can place the drilling point directly through a finished tile where an incorrect accessory can damage more than the hole itself.

ICCONS includes Cera Expert tile-drilling products within its drilling-accessory range.

Before drilling:

► Identify the tile material
► Confirm hole diameter
► Establish what sits behind the tile
► Check the appropriate drilling method
► Mark the position accurately
► Select tooling suited to the surface

For accurate positioning before drilling finished materials, browse Measuring & Layout Tools.

Check both the visible surface & the substrate behind it before committing the bit to the marked position.

Ratio Quick Handles Larger Openings Through Suitable Masonry

Plumbing, electrical & other service work can require an opening considerably larger than a conventional drill-bit hole.

ICCONS Ratio Quick Core Bits are documented in:

► 50 mm
► 65 mm
► 80 mm

They are intended for suitable soft concrete & masonry applications.

The supporting system includes:

► Ratio Quick Core Pilot Bit
► Ratio Quick Adaptor SDS Plus
► Ratio Quick Adaptor SDS Max

For wider concrete & masonry drilling equipment, browse Concrete Cutting & Drilling Tools.

Determine the penetration diameter first then match the supporting components to the rotary-hammer system being used.

Ratio Quick & Diamond Coring Serve Different Drilling Setups

Larger holes can be produced with different equipment systems depending on the substrate, diameter & work being undertaken.

Ratio Quick is an ICCONS core-bit system for compatible soft concrete & masonry applications using SDS Plus or SDS Max adaptors.

Dedicated diamond coring can involve different machines, core barrels, stands, water-management equipment & supporting accessories.

Requirement

Ratio Quick

Diamond Coring Setup

Documented use

Soft concrete & masonry

Dedicated diamond drilling

Connection

SDS Plus / SDS Max adaptor

Depends on coring system

Ratio Quick diameters

50, 65 & 80 mm

Depends on selected system

Equipment focus

Core, pilot & rotary-hammer adaptor

Core drill, barrel & supporting equipment

Choose between systems according to the actual penetration & equipment requirements of the job.

Bit Kits Work Best When Their Profiles Match Everyday Fasteners

An organised assortment becomes useful when it contains the drive profiles the crew repeatedly encounters.

ICCONS FastDrive includes multi-piece bit kits alongside BITZ storage options.

A documented 10-piece impact kit combines impact insert bits across PH2, SQ2 & HX5 profiles with a bit holder.

These kits can suit:

► Maintenance vehicles
► Builder toolboxes
► Installation crews
► Fit-out teams
► Workshop benches
► Service technicians

For broader grouped tooling, browse Tool Sets.

Compare the included profiles with the fasteners used regularly rather than choosing from piece count alone.

Practical Checks Before Drilling or Driving

Small accessories transfer the tool's output directly into the fixing or material, making condition & compatibility worth checking before work starts.

► Confirm the recess. Similar-looking drive profiles are not interchangeable.
► Separate impact from standard use. Match the accessory to the operating environment.
► Inspect the holder when retention changes. The insert bit may not be causing the problem.
► Choose socket depth deliberately. Deep sockets solve specific clearance requirements.
► Check pilot drills before decking work. Worn or damaged Smart-Bit pilot components can be replaced where compatible.
► Treat fibre cement separately from timber. Select preparation equipment around the board being installed.
► Check the hidden substrate before tile drilling. The finished surface is only one part of the drilling task.
► Match Ratio Quick adaptors to the rotary hammer. SDS Plus & SDS Max use their respective compatible adaptors.
► Use right-angle equipment to overcome restricted access. The fastener still requires the correct driver profile.

For practical preparation before demanding periods on site, read Spring Jobsite Prep Getting Your Gear Ready.