Car Servicing & Workshop Repairs

The right hydraulic floor jack should do more than lift a vehicle. It needs to fit beneath the manufacturer's approved lifting point, provide enough lifting travel for the job & operate safely within the available garage space.

Shop hydraulic floor jacks & trolley jacks at Industrial Shed for suitable car servicing, wheel changes, brake maintenance & general automotive workshop tasks. Compare rated lifting capacities of 1,350 kg, 1,850 kg & 2,000 kg across the listed Kincrome models.

Before choosing a jack, consider vehicle clearance, saddle height, lifting range, floor conditions & the load imposed during the intended lift.

Start With Your Vehicle's Ground Clearance

Low vehicles can present a challenge before lifting even begins.

A jack may have enough rated capacity but still be unable to reach the approved lifting point because its saddle or front frame sits too high.

For sports cars, lowered vehicles & other low-clearance applications, compare the manufacturer's stated minimum saddle height with the actual access available beneath the vehicle.

Higher-clearance vehicles present a different challenge: the jack must have sufficient maximum lifting height to achieve the required working position.

Avoid choosing solely from product descriptions such as low-profile or heavy-duty. The actual dimensions determine suitability.

Compare the Available Hydraulic Floor Jacks

The current range includes three trolley jack capacity options.

Important: The stated capacity is the jack's rated lifting load, not a blanket approval to lift any vehicle with a lower total mass.

For each model, confirm the minimum height, maximum height, saddle arrangement & dimensions on its individual product listing. These figures should not be inferred from capacity alone.

Five Checks That Prevent Buying the Wrong Trolley Jack

Identify the Approved Lifting Point

Use the vehicle manufacturer's instructions. Not every convenient-looking chassis component is designed to carry lifting loads.

Measure the Available Clearance

Check the height at the actual lifting point, including any bodywork the jack must pass beneath.

Confirm the Required Lifting Travel

A jack must reach the necessary height while allowing safe placement of appropriate vehicle support equipment.

Assess the Workshop Floor

Trolley jacks are intended for suitable firm, level surfaces. Uneven or unstable ground can affect jack movement & load stability.

Plan the Full Support Arrangement

A hydraulic jack raises the vehicle; it does not replace appropriately rated support stands.

For this final step, explore Jack Stands when selecting suitable vehicle support equipment.

Hydraulic Floor Jack vs Bottle Jack

These tools may use similar hydraulic principles, but their shapes & applications differ.

A trolley jack uses a wheeled chassis & lifting arm to reach beneath a suitable vehicle.

A bottle jack lifts vertically from a more compact base, which can be useful for specified applications where there is adequate clearance.

Neither is universally better. Minimum height, load capacity, lifting travel & the manufacturer's approved use determine the correct choice.

Compare Bottle Jacks if a vertical hydraulic jack may better suit your task.

Think Beyond the First Lift

Changing a wheel may be straightforward, but underbody maintenance often requires more working space, careful load support & a clear procedure.

Prepare the work area before raising the vehicle. Position suitable wheel chocks, remove unnecessary equipment from the lifting zone & ensure the jack can move as intended during the lift.

Never move or work beneath a vehicle supported only by a hydraulic floor jack.

For related servicing tools, browse Workshop Equipment.

Maintenance That Helps Keep a Floor Jack Reliable

Hydraulic equipment should be checked before each use, especially after extended storage.

Inspect the frame, saddle, wheels & handle for damage. Look for fluid leaks, corrosion or unusual movement.

If the jack fails to raise smoothly, creeps under load or cannot lower in a controlled manner, stop using it & follow the manufacturer's servicing instructions.

Use only specified hydraulic fluid & approved replacement parts. Improvised repairs can compromise lifting performance.

Safety & Care

• Lift only at vehicle manufacturer-approved points.

• Confirm the jack's rated capacity & required lifting range.

• Operate on a suitable firm, level surface.

• Chock wheels & secure the vehicle as instructed.

• Keep hands, feet & tools clear of moving jack components.

• Never work beneath a vehicle supported solely by a jack.

• Remove leaking, damaged or malfunctioning equipment from service.

Hydraulic Floor Jacks FAQs

Do I Need a Low-Profile Jack for a Standard Passenger Car?

Not necessarily. Measure the clearance at the vehicle's approved lifting point & compare it with the jack's minimum saddle height. A standard trolley jack may be suitable where access permits.

Does a Higher Tonne Rating Mean the Jack Lifts Higher?

No. Lifting capacity & maximum saddle height are separate specifications. A higher-capacity jack may not provide the reach required for your vehicle.

Can I Use a Trolley Jack on a Sloping Driveway?

A sloping surface can compromise vehicle & jack stability. Use the equipment only on a suitable firm, level surface in accordance with the manufacturer's instructions.

Why Does My Floor Jack Lower Slowly?

Lowering speed can be affected by the release mechanism, load & hydraulic condition. Follow the operating instructions; if movement is abnormal or uncontrolled, remove the jack from service.

Industrial Shed Support

Compare hydraulic floor jacks by rated capacity, minimum height, maximum lift, frame dimensions & vehicle compatibility. Industrial Shed supplies automotive lifting equipment for Australian garages, maintenance workshops & trade applications.

See Shipping & Delivery for delivery information or Warranty & Parts Support for product assistance.