► ICCONS® | Pipe Clips

Self-Locking Support for PVC, Copper & PEX Pipe Runs Keeping pipework straight, supported & easy to install starts with matching the clip to the actual pipe diameter. ICCONS® | Pipe Clips include self-locking polyamide clips designed to secure compatible PVC, copper & PEX pipework across plumbing, mechanical, air-conditioning, refrigeration &...

Self-Locking Support for PVC, Copper & PEX Pipe Runs

Keeping pipework straight, supported & easy to install starts with matching the clip to the actual pipe diameter. ICCONS® | Pipe Clips include self-locking polyamide clips designed to secure compatible PVC, copper & PEX pipework across plumbing, mechanical, air-conditioning, refrigeration & building-service installations.

For plumbers, mechanical contractors, refrigeration technicians, installers & maintenance crews, the documented multi-diameter range covers pipe sizes from 14–42 mm. Individual clip sizes accommodate several pipe diameters within their stated range while the self-locking design closes as compatible pipe is pushed into position. When planning the complete installation, compare Anchors & Wall Plugs, prepare suitable fixing points with  Drill Accessories or review Screws & Anchors where the substrate calls for another compatible fixing method.

► Self-locking polyamide construction
► Automatic closure around compatible pipe
► Multi-diameter sizing
► Documented pipe range from 14–42 mm
► Suitable for compatible PVC pipe
► Suitable for compatible copper pipe
► Suitable for hot & cold PEX applications
► Multiple fixing methods
► Alignment indication for accurate positioning
► Designed to accommodate pipe movement within the clip
► Suitable for documented warm-water pipe applications up to 90°C

What Are ICCONS® Pipe Clips?

A well-selected pipe clip supports the service without turning every fixing point into a multi-part assembly.

These self-locking polyamide clips are designed to embrace compatible pipe as it is pushed into the channel. Once the correct clip has been fixed in position, the pipe engages with the clip without requiring a separate closing component at every support point.

The design also accommodates appropriate pipe movement.

That becomes particularly important where operating temperatures cause expansion & contraction through the service run.

For practical guidance on matching fixings to the materials being installed, read Why Good Fasteners Matter More Than the Tool You Drive Them With.

Four Clip Ranges Cover Pipe Diameters From 14–42 mm

Knowing the outside pipe diameter immediately narrows the clip choice.

The documented range includes:

Part Number

Pipe Diameter

Configuration

GTQC14-18

14–18 mm

Self-locking pipe clip

GTQC20-25

20–25 mm

Self-locking pipe clip

GTQC26-32

26–32 mm

Self-locking pipe clip

GTQC35-42

35–42 mm

Self-locking pipe clip

Multi-diameter sizing can simplify preparation where several compatible pipe sizes fall within the same clip range.

Confirm the actual outside diameter before selecting stock.

Nominal pipe descriptions can differ from measured outside dimensions, so the service itself should guide the final choice.

Start With the Pipe Before Choosing the Fixing

The pipe determines the clip; the substrate then determines how that clip should be attached.

Before installation, identify:

► Pipe material
► Outside diameter
► Operating temperature
► Horizontal or vertical route
► Base material
► Intended fixing method
► Applicable pipe-system requirements

Once those details are known, choose the appropriate clip range.

A clip marked 20–25 mm should be used around compatible pipe within that documented diameter range rather than selected solely from a nominal pipe description.

PVC, Copper & PEX Bring Different Installation Considerations

Two pipes following the same wall can require different support decisions once their material & operating conditions are considered.

Documented applications include:

► PVC pipe
► Copper pipe
► Hot PEX pipe
► Cold PEX pipe

PVC, copper & PEX can differ in outside dimensions, temperature response & movement characteristics.

Check the requirements applying to the actual pipe system rather than transferring the same assumptions from one material to another.

Where several pipe materials share a plant room or service corridor, identify them before clips are distributed to installers.

Hot-Water Services Need Room to Move

A straight pipe run at installation temperature may behave differently once hot water begins moving through it.

The polyamide clip is designed to embrace compatible pipe while accommodating pipe dilatation. This allows appropriate movement within the support rather than treating every clip position as a rigid restraint.

The system is documented for warm-water pipe applications up to 90°C within the applicable installation requirements.

Consider that rating alongside:

► Pipe material
► Actual operating temperature
► Pipe manufacturer instructions
► Support spacing
► Expansion provisions
► Direction changes
► Fixed points elsewhere in the system

The clip forms one part of the complete pipe-support arrangement.

Self-Locking Clips Can Simplify Long Service Runs

Repeated pipe supports become much easier to install when the closure mechanism is already built into the clip.

After the appropriate clip has been fixed, compatible pipe can be pushed into the channel to engage the self-locking design.

This format can be useful across:

► Plumbing installations
► Mechanical services
► Air-conditioning work
► Refrigeration installations
► Plant rooms
► Commercial service areas
► Maintenance projects

The convenience of self-locking installation still depends on correct sizing, accurate set-out & a suitable fixing behind the clip.

Use the Alignment Indicator Before Installing the Pipe

Small positioning errors become increasingly visible as a pipe run extends across a wall or ceiling.

The clip incorporates an alignment indication to assist set-out.

Before installing multiple clips, establish:

► Route centreline
► Changes in direction
► Pipe entries
► Equipment connections
► Penetrations
► Junctions
► Clearance from neighbouring services

For longer runs,  Measuring & Layout Tools can help maintain consistent positioning.

Complete the alignment work while every fixing point remains visible.

Match the Clip Fixing to the Base Material

Correct clip sizing solves the pipe-side requirement but the connection behind the clip still needs its own assessment.

The self-locking clip supports multiple fixing methods, with the appropriate choice depending on the substrate & installation.

Check the material receiving the fixing before work begins.

Depending on the project, fixing locations may involve:

► Concrete
► Masonry
► Timber
► Suitable building supports
► Purpose-designed support systems

A fixing suitable for one substrate should not automatically be carried onto another surface simply because the pipe & clip remain unchanged.

Screw Fixing or Compatible Gas-Nailer Installation?

Access, substrate & repetition can influence how the clips are attached along a service route.

The self-locking clip is designed for installation using compatible screws or gas-nailer systems.

A screw fixing may suit one area while compatible nailer installation can provide a practical approach across suitable repetitive work.

Before deciding, confirm:

Check

What Matters

Pipe

Material & outside diameter

Clip

Correct 14–18, 20–25, 26–32 or 35–42 mm range

Substrate

Actual base material

Fixing

Compatibility with clip & substrate

Equipment

Suitable installation tool

Route

Alignment, access & transitions

Choose the fixing method around the installation rather than simply using whichever tool happens to be closest.

Corners, Valves & Equipment Connections Need Their Own Plan

Straight pipe is usually forgiving; crowded transitions are where poor support positioning becomes obvious.

Review clip locations around:

► Bends
► Valves
► Equipment connections
► Penetrations
► Branches
► Vertical transitions
► Changes in pipe material
► Congested service areas

Allow enough room for the pipe to follow its intended route without forcing it sideways to meet an inconvenient clip position.

Where an unusual connection needs another fastening arrangement,  Specialty Fasteners & Fixings provides additional options to consider.

Support Spacing Should Follow the Pipe System

There is no single spacing measurement that belongs to every pipe material, diameter & service condition.

Appropriate support intervals can depend on:

► Pipe material
► Pipe diameter
► Service temperature
► Horizontal or vertical installation
► Pipe manufacturer requirements
► Applicable standards
► Project specification
► Direction changes
► Equipment connections

Follow the requirements governing the pipe system being installed.

Avoid carrying a spacing rule from one service onto another without confirming that the same requirement applies.

Existing Plant Rooms Can Hide Difficult Fixing Conditions

Maintenance & upgrade work often brings new pipework into areas already crowded with old supports, repairs & multiple services.

Inspect the route for:

► Previous fixing holes
► Damaged substrate
► Existing anchors
► Crowded service zones
► Changes in wall construction
► Pipe repairs
► Insulation
► Restricted tool access

Move an unsuitable fixing position where necessary rather than forcing a new clip into damaged material.

Good positioning should support the new service without unnecessarily interfering with existing pipework or equipment access.

Keep Each Diameter Range Clearly Identified

Similar-looking clips are easy to mix once several cartons or containers are open.

Separate stock by:

► Part number
► Diameter range
► Work zone
► Pipe material where useful
► Installation stage

GTQC20-25 & GTQC26-32 cover neighbouring size ranges but should not be treated as interchangeable.

Keep product identification with the clips until installation is complete.

For crews preparing consumables before larger installation stages, Spring Jobsite Prep Getting Your Gear Ready provides further practical preparation guidance.

Let the First Pipe Confirm the Clip Choice

The first installed section provides a quick check that the measured diameter, selected clip & actual service agree.

Inspect:

► Pipe fit
► Self-locking engagement
► Clip alignment
► Fixing stability
► Pipe position
► Appropriate movement
► Clearance from surrounding work

If the pipe does not engage naturally, confirm its outside diameter & clip range before continuing.

Do not force an oversized pipe into the clip or accept an obviously loose fit simply to keep the installation moving.

Allow for Movement Where the Service Requires It

Secure support does not always mean locking every section of pipe against all movement.

Temperature changes can produce expansion & contraction along a service.

Account for:

► Pipe manufacturer instructions
► Operating temperature
► Fixed points
► Expansion provisions
► Direction changes
► Equipment connections
► Overall support arrangement

The clip's ability to accommodate pipe dilatation is useful only when the remainder of the system has also been planned correctly.

When Does Another Pipe Support Make More Sense?

Self-locking surface-mounted clips have a defined role but they are not intended to support every type of pipe installation.

Consider another arrangement where:

► Pipe diameter falls outside the documented range
► Heavy suspension is required
► The service needs substantial stand-off from the surface
► Multiple pipes require a shared support system
► Project documentation specifies another support method
► Loads require engineered suspension hardware

For installations requiring substantially different threaded connections,  Structural Fasteners & Bolts provides another fastening family to consider.

Match the support system to the service rather than trying to make one clip type cover every condition.

Six Checks Before Installing a Full Pipe Run

A quick check at the beginning can prevent the same sizing or positioning problem from continuing through an entire installation.

Pipe Diameter

Does the actual outside diameter fall within the selected clip range?

Pipe Material

Is the service PVC, copper, PEX or another material requiring separate confirmation?

Temperature

Will operating conditions introduce expansion or contraction that needs to be accommodated?

Substrate

What material will receive the clip fixing?

Route

Have bends, valves, equipment connections, penetrations & neighbouring services been considered?

First Clip

Does the pipe engage correctly while the clip remains aligned & securely fixed?

Resolve those points before moving into repetitive installation.

Why Source ICCONS® Pipe Clips Through Industrial Shed?

Correct diameter selection before ordering makes it easier to send installers to site with the clips that belong with each pipe run.

Industrial Shed supports plumbers, mechanical contractors, air-conditioning installers, refrigeration technicians, builders & maintenance teams sourcing fastening products for active installations.

For trade businesses coordinating recurring project requirements, Trade support Solutions provides support for trade purchasing.

Need help separating similar clip ranges before ordering? Call us at with the pipe diameter, pipe material, substrate & intended fixing method.

Set the Support Points Before the Pipe Goes In

A tidy pipe run is much easier to achieve when sizing, alignment & fixing decisions are settled before installation starts.

Confirm the outside diameter, choose the appropriate clip range then mark the route around bends, valves, penetrations & equipment connections. Match the fixing method to the substrate & use the first installed section to confirm that the pipe engages naturally.

For temperature-changing services, allow the pipe system to move as intended while maintaining appropriate support along the route.

Choose ICCONS Pipe Clips where compatible 14–42 mm PVC, copper or PEX pipe needs self-locking support matched to the pipe diameter, substrate & installation method.

Frequently Asked Questions

We have 20 mm & 25 mm pipe on the same project. Can one clip size cover both?

The GTQC20-25 range accommodates compatible pipe diameters from 20–25 mm. Confirm the actual outside diameter & complete installation requirements before selection.

Can ICCONS Pipe Clips support hot-water pipe?

The documented self-locking polyamide clips are suitable for warm-water pipe applications up to 90°C within the applicable system requirements. Confirm the pipe material, operating temperature & installation requirements.

Does the clip close when the pipe is pushed into it?

Yes. The self-locking design is intended to close around compatible pipe as it is pushed into the clip.

Are these clips limited to PVC installations?

No. Compatible copper plus hot & cold PEX pipe are also documented applications.

Can the clips be fixed using a gas nailer?

The clip is designed for compatible screw or gas-nailer installation. The fixing method still needs to suit the clip, substrate, equipment & complete installation.

Which clip range should we choose?

Confirm the actual pipe diameter then select the appropriate 14–18, 20–25, 26–32 or 35–42 mm range.

Brands

► ICCONS® | Pipe Clips

Self-Locking Support for PVC, Copper & PEX Pipe Runs

Keeping pipework straight, supported & easy to install starts with matching the clip to the actual pipe diameter. ICCONS® | Pipe Clips include self-locking polyamide clips designed to secure compatible PVC, copper & PEX pipework across plumbing, mechanical, air-conditioning, refrigeration & building-service installations.

For plumbers, mechanical contractors, refrigeration technicians, installers & maintenance crews, the documented multi-diameter range covers pipe sizes from 14–42 mm. Individual clip sizes accommodate several pipe diameters within their stated range while the self-locking design closes as compatible pipe is pushed into position. When planning the complete installation, compare Anchors & Wall Plugs, prepare suitable fixing points with  Drill Accessories or review Screws & Anchors where the substrate calls for another compatible fixing method.

► Self-locking polyamide construction
► Automatic closure around compatible pipe
► Multi-diameter sizing
► Documented pipe range from 14–42 mm
► Suitable for compatible PVC pipe
► Suitable for compatible copper pipe
► Suitable for hot & cold PEX applications
► Multiple fixing methods
► Alignment indication for accurate positioning
► Designed to accommodate pipe movement within the clip
► Suitable for documented warm-water pipe applications up to 90°C

What Are ICCONS® Pipe Clips?

A well-selected pipe clip supports the service without turning every fixing point into a multi-part assembly.

These self-locking polyamide clips are designed to embrace compatible pipe as it is pushed into the channel. Once the correct clip has been fixed in position, the pipe engages with the clip without requiring a separate closing component at every support point.

The design also accommodates appropriate pipe movement.

That becomes particularly important where operating temperatures cause expansion & contraction through the service run.

For practical guidance on matching fixings to the materials being installed, read Why Good Fasteners Matter More Than the Tool You Drive Them With.

Four Clip Ranges Cover Pipe Diameters From 14–42 mm

Knowing the outside pipe diameter immediately narrows the clip choice.

The documented range includes:

Part Number

Pipe Diameter

Configuration

GTQC14-18

14–18 mm

Self-locking pipe clip

GTQC20-25

20–25 mm

Self-locking pipe clip

GTQC26-32

26–32 mm

Self-locking pipe clip

GTQC35-42

35–42 mm

Self-locking pipe clip

Multi-diameter sizing can simplify preparation where several compatible pipe sizes fall within the same clip range.

Confirm the actual outside diameter before selecting stock.

Nominal pipe descriptions can differ from measured outside dimensions, so the service itself should guide the final choice.

Start With the Pipe Before Choosing the Fixing

The pipe determines the clip; the substrate then determines how that clip should be attached.

Before installation, identify:

► Pipe material
► Outside diameter
► Operating temperature
► Horizontal or vertical route
► Base material
► Intended fixing method
► Applicable pipe-system requirements

Once those details are known, choose the appropriate clip range.

A clip marked 20–25 mm should be used around compatible pipe within that documented diameter range rather than selected solely from a nominal pipe description.

PVC, Copper & PEX Bring Different Installation Considerations

Two pipes following the same wall can require different support decisions once their material & operating conditions are considered.

Documented applications include:

► PVC pipe
► Copper pipe
► Hot PEX pipe
► Cold PEX pipe

PVC, copper & PEX can differ in outside dimensions, temperature response & movement characteristics.

Check the requirements applying to the actual pipe system rather than transferring the same assumptions from one material to another.

Where several pipe materials share a plant room or service corridor, identify them before clips are distributed to installers.

Hot-Water Services Need Room to Move

A straight pipe run at installation temperature may behave differently once hot water begins moving through it.

The polyamide clip is designed to embrace compatible pipe while accommodating pipe dilatation. This allows appropriate movement within the support rather than treating every clip position as a rigid restraint.

The system is documented for warm-water pipe applications up to 90°C within the applicable installation requirements.

Consider that rating alongside:

► Pipe material
► Actual operating temperature
► Pipe manufacturer instructions
► Support spacing
► Expansion provisions
► Direction changes
► Fixed points elsewhere in the system

The clip forms one part of the complete pipe-support arrangement.

Self-Locking Clips Can Simplify Long Service Runs

Repeated pipe supports become much easier to install when the closure mechanism is already built into the clip.

After the appropriate clip has been fixed, compatible pipe can be pushed into the channel to engage the self-locking design.

This format can be useful across:

► Plumbing installations
► Mechanical services
► Air-conditioning work
► Refrigeration installations
► Plant rooms
► Commercial service areas
► Maintenance projects

The convenience of self-locking installation still depends on correct sizing, accurate set-out & a suitable fixing behind the clip.

Use the Alignment Indicator Before Installing the Pipe

Small positioning errors become increasingly visible as a pipe run extends across a wall or ceiling.

The clip incorporates an alignment indication to assist set-out.

Before installing multiple clips, establish:

► Route centreline
► Changes in direction
► Pipe entries
► Equipment connections
► Penetrations
► Junctions
► Clearance from neighbouring services

For longer runs,  Measuring & Layout Tools can help maintain consistent positioning.

Complete the alignment work while every fixing point remains visible.

Match the Clip Fixing to the Base Material

Correct clip sizing solves the pipe-side requirement but the connection behind the clip still needs its own assessment.

The self-locking clip supports multiple fixing methods, with the appropriate choice depending on the substrate & installation.

Check the material receiving the fixing before work begins.

Depending on the project, fixing locations may involve:

► Concrete
► Masonry
► Timber
► Suitable building supports
► Purpose-designed support systems

A fixing suitable for one substrate should not automatically be carried onto another surface simply because the pipe & clip remain unchanged.

Screw Fixing or Compatible Gas-Nailer Installation?

Access, substrate & repetition can influence how the clips are attached along a service route.

The self-locking clip is designed for installation using compatible screws or gas-nailer systems.

A screw fixing may suit one area while compatible nailer installation can provide a practical approach across suitable repetitive work.

Before deciding, confirm:

Check

What Matters

Pipe

Material & outside diameter

Clip

Correct 14–18, 20–25, 26–32 or 35–42 mm range

Substrate

Actual base material

Fixing

Compatibility with clip & substrate

Equipment

Suitable installation tool

Route

Alignment, access & transitions

Choose the fixing method around the installation rather than simply using whichever tool happens to be closest.

Corners, Valves & Equipment Connections Need Their Own Plan

Straight pipe is usually forgiving; crowded transitions are where poor support positioning becomes obvious.

Review clip locations around:

► Bends
► Valves
► Equipment connections
► Penetrations
► Branches
► Vertical transitions
► Changes in pipe material
► Congested service areas

Allow enough room for the pipe to follow its intended route without forcing it sideways to meet an inconvenient clip position.

Where an unusual connection needs another fastening arrangement,  Specialty Fasteners & Fixings provides additional options to consider.

Support Spacing Should Follow the Pipe System

There is no single spacing measurement that belongs to every pipe material, diameter & service condition.

Appropriate support intervals can depend on:

► Pipe material
► Pipe diameter
► Service temperature
► Horizontal or vertical installation
► Pipe manufacturer requirements
► Applicable standards
► Project specification
► Direction changes
► Equipment connections

Follow the requirements governing the pipe system being installed.

Avoid carrying a spacing rule from one service onto another without confirming that the same requirement applies.

Existing Plant Rooms Can Hide Difficult Fixing Conditions

Maintenance & upgrade work often brings new pipework into areas already crowded with old supports, repairs & multiple services.

Inspect the route for:

► Previous fixing holes
► Damaged substrate
► Existing anchors
► Crowded service zones
► Changes in wall construction
► Pipe repairs
► Insulation
► Restricted tool access

Move an unsuitable fixing position where necessary rather than forcing a new clip into damaged material.

Good positioning should support the new service without unnecessarily interfering with existing pipework or equipment access.

Keep Each Diameter Range Clearly Identified

Similar-looking clips are easy to mix once several cartons or containers are open.

Separate stock by:

► Part number
► Diameter range
► Work zone
► Pipe material where useful
► Installation stage

GTQC20-25 & GTQC26-32 cover neighbouring size ranges but should not be treated as interchangeable.

Keep product identification with the clips until installation is complete.

For crews preparing consumables before larger installation stages, Spring Jobsite Prep Getting Your Gear Ready provides further practical preparation guidance.

Let the First Pipe Confirm the Clip Choice

The first installed section provides a quick check that the measured diameter, selected clip & actual service agree.

Inspect:

► Pipe fit
► Self-locking engagement
► Clip alignment
► Fixing stability
► Pipe position
► Appropriate movement
► Clearance from surrounding work

If the pipe does not engage naturally, confirm its outside diameter & clip range before continuing.

Do not force an oversized pipe into the clip or accept an obviously loose fit simply to keep the installation moving.

Allow for Movement Where the Service Requires It

Secure support does not always mean locking every section of pipe against all movement.

Temperature changes can produce expansion & contraction along a service.

Account for:

► Pipe manufacturer instructions
► Operating temperature
► Fixed points
► Expansion provisions
► Direction changes
► Equipment connections
► Overall support arrangement

The clip's ability to accommodate pipe dilatation is useful only when the remainder of the system has also been planned correctly.

When Does Another Pipe Support Make More Sense?

Self-locking surface-mounted clips have a defined role but they are not intended to support every type of pipe installation.

Consider another arrangement where:

► Pipe diameter falls outside the documented range
► Heavy suspension is required
► The service needs substantial stand-off from the surface
► Multiple pipes require a shared support system
► Project documentation specifies another support method
► Loads require engineered suspension hardware

For installations requiring substantially different threaded connections,  Structural Fasteners & Bolts provides another fastening family to consider.

Match the support system to the service rather than trying to make one clip type cover every condition.

Six Checks Before Installing a Full Pipe Run

A quick check at the beginning can prevent the same sizing or positioning problem from continuing through an entire installation.

Pipe Diameter

Does the actual outside diameter fall within the selected clip range?

Pipe Material

Is the service PVC, copper, PEX or another material requiring separate confirmation?

Temperature

Will operating conditions introduce expansion or contraction that needs to be accommodated?

Substrate

What material will receive the clip fixing?

Route

Have bends, valves, equipment connections, penetrations & neighbouring services been considered?

First Clip

Does the pipe engage correctly while the clip remains aligned & securely fixed?

Resolve those points before moving into repetitive installation.